Miele T 8626 WP Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 60

background image

Other problems

Problem

Possible cause

Remedy

The drying
process goes on
too long or even
switches off.

Please check all the possible causes and switch the dryer
off and then back on again.

Ventilation to and from the
dryer may be insufficient (e.g
because it is installed in a
small room). This has caused
the temperature in the room
to rise sharply.

Open a door or window while
the dryer is in operation for
increased air flow.

The fluff filters and fine filters
are clogged with fluff,
detergent residues or hair.

– Remove any fluff, hair or

residual detergents:
. . . from the fluff filters in
the door and the door
opening.
. . . from the fine filters in
front of the heat exchanger
unit.

– Clean the fluff filters and, if

necessary, the fine filters.

The fluff filters and the fine
filters were still wet when they
were replaced.

The fluff filters and fine filters
must be dry.

The laundry has not been
spun sufficiently.

Make sure that your laundry
is thoroughly spun at the
appropriate spin speed in the
washing machine.

The tumble dryer has been
overloaded.

Do not exceed the maximum
load for the programme
selected.

Metallic components, e.g.
zips have prevented the
dryer from registering the
correct moisture level in the
laundry.

– Open zips next time.

If the problem occurs again,
dry garments with long zips
using the

Warm air

programme (timed drying).

Problem solving guide

38

«
...
36
37
38
39
40
...
»

Содержание T 8626 WP





























































Отзывы:

Нет отзывов

Похожие инструкции для T 8626 WP

Бренд: Oster Страницы: 7

Бренд: Maytag Страницы: 40

Бренд: Beautural Страницы: 4

Бренд: V-ZUG Страницы: 10

Бренд: Taurus Страницы: 52

Бренд: Ga.Ma Страницы: 38

Бренд: Grundig Страницы: 25

Бренд: DeLUX Страницы: 383

Centauro ICL2040 Series

Бренд: mabe Страницы: 138

Бренд: Esatto Страницы: 24

Бренд: Magnani Страницы: 40

Бренд: Linsar Страницы: 12

Бренд: Verloni Страницы: 11

Бренд: Optimum Страницы: 45

Бренд: Haden Страницы: 18

Бренд: TriStar Страницы: 31

LAVATHERM T8DHC862B

Бренд: AEG Страницы: 27

Бренд: AEG Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды