Miele T 8626 WP Скачать руководство пользователя страница 26

Страница: 26 / 60

Once a programme has started

- changing the programme

You cannot change to another
programme once a programme has
started (this prevents unintentional
alterations).
If an attempt is made to change a
selection:

Option not possible

will

appear in the display.

It is still possible to select or deselect
the

Anti-crease

and

Buzzer

extra

options.

You will need to cancel the current
programme before you can select a
new one.

- cancelling the programme and then
selecting a different programme

Press the

Start/Stop

button.

Cancel programme

will appear in the

display.

Confirm by pressing the right hand

Menu

button under

The items will be cooled down,
depending on the temperature
reached and how long they have
been dried for.

If you press the

Start/Stop

button

during the cooling down phase and
confirm by pressing the right hand

Menu

button under

Finished

will

appear in the display.

Switch the dryer off.

Switch the dryer back on again.

Select another programme and start
it.

Note: A programme can also be
cancelled by turning the programme
selector to

Stop

- cancelling the programme and then
removing the laundry

Proceed as described in "Adding or
removing laundry after a programme
has started" below.

Switch the dryer off after closing the
door.

Adding or removing laundry
after a programme has started

Press the

Door

button.

Open the door.

Add or remove items as required.

Close the door.

Press the

Start/Stop

button.

Time remaining

The time left shown in the display may
now vary from the actual drying time.

Changing the programme sequence

Содержание T 8626 WP





























































Результаты поиска

Содержание T 8626 WP

Отзывы:

Похожие инструкции для T 8626 WP

Бренды по названию

Популярные бренды

Miele T 8626 WP, Руководство по эксплуатации

Результаты поиска

Содержание T 8626 WP

Отзывы:

Похожие инструкции для T 8626 WP

Бренды по названию

Популярные бренды