Microplex M204 Скачать руководство пользователя страница 118

Страница: 118 / 204

110

USING THE M204’S COMMAND SET: npsh Command Set

store tcpip

ifnum addr ipaddress

Store the ipaddress for the NIT module specified by ifnum.

ifnum is the Interface Number labelled on each of the M204’s PCMCIA slots.

store tcpip

ifnum frametype [[-]ethernet2] [[-]802.2snap]

Control the frame type(s) used by the NIT module specified by ifnum.

store tcpip

ifnum mask netmask

Store the netmask for the NIT module specified by ifnum.

store tcpip

ifnum opts [[-]rarp] [[-]bootp]

Enable or disable the RARP and BOOTP for the NIT module specified by
ifnum.

store tcpip opts [-]ipforward

Enables the IP forwarding or routing functions of the M204. By default, the
gateway is disabled. This command must be used in conjuction with the

store tcpip proxy

command below.

store tcpip proxy add [host|net]

targetipaddress [/tar-

getnetmask]

Enables the M204 to respond to ARP requests for IP addresses that are differ-
ent than the interface configuration of the M204.

store tcpip proxy del

targetipaddress

Removes this entry from the proxy ARP table.

store tcpip route add|del default

routeripaddress ifnum

Add or delete a default router entry in the M204’s routing table for the NIT
module specified by ifnum.

Note

Содержание M204













































































































































































































Результаты поиска

Содержание M204

Отзывы:

Похожие инструкции для M204

Бренды по названию

Популярные бренды

Microplex M204, Руководство по установке и настройке

Результаты поиска

Содержание M204

Отзывы:

Похожие инструкции для M204

Бренды по названию

Популярные бренды