manualshive.com logo in svg

Microplex M204, Руководство по установке и настройке

Поделиться
Скачать
Microplex M204 Скачать руководство пользователя страница 183

M204 SPECIFICATIONS: Hardware Specifications

173

An invalid license mask and key forces the M204 into license-
violation mode after three minutes of operation. Make sure the
S3 jumper is on EEPROM Enable and if it continues, check to see
if the keys are enabled. Please see list key on page 86. A reboot
will temporarily fix this.

Unrecoverable errors detected by the M204 firmware force the
Print Server into Firmware Panic mode. Manually reset the M204
to resume normal operation.

The watchdog timer is a hardware device that resets the system if
not serviced regularly by the CPU. The purpose of the watchdog
is to prevent the CPU from entering an infinite loop because of
some hardware or firmware problem. After a watchdog interrupt,
some diagnostic information is saved for debugging and the
M204 resumes operation in Auto-Reset Mode. The M204 will
auto-reset up to 16 times before entering non-operational Watch-
dog Halt.

Unsupported interrupts force the M204 into this non-operational
mode and typically indicate a hardware problem.

Table 9:

Run and Auto-Reset Mode Description

STAT

Rate

Indicates

Flashes On

once per second

Normal Mode, IP
address configured

Flashes On

2.5 times per second

Monitor Mode, IP
address not configured

Flashes Off

once per second

Normal Mode, IP
address configured

Flashes Off

2.5 times per second

Monitor or Download
Mode, IP address not
configured

Flashes off

once per 2 seconds

Download Mode, IP
address configured

License Violation

Firmware Panic

Watchdog Halt

Spurious Interrupt

Содержание M204













































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды