MHS Boilers STRATA1 38 COMBI Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 71

MHS Boilers STRATA1 38 COMBI Скачать руководство пользователя страница 7

4.0 delivery consignment

/unpacking the boiler

The boiler is delivered as a consignment of a palleted carton containing the boiler and associated

fittings, plus any other optional ancillary flue or control components in separate cartons.

The boiler carton contains:-

●

Assembled boiler.

●

Wall mounting bracket.

●

Fittings bag including: condense waste outlet hose union assembly, outside air temperature sensor c/w
wall fixings and 1/2" BSP inlet 3/4" BSP outlet safety pressure relief valve set 3 bar.

To unpack the boiler, the palleted carton should be laid on the floor. Carefully cut the nylon bands and

lift away fibre board protective panel. Open carton top and lift out wall hanging bracket and fittings bag.
Remove packing material and lift away bottomless carton. With 2 men, carefully lift boiler from palette by
holding grey rear chassis only.

To remove the casing from the boiler, slacken the screw in the underside of the casing, unlatch left and

right hand catches on underside of case, pull casing slightly to the front and lift upwards to disengage casing
hooks from rear chassis and then remove casing to the front.

5.0 boiler

location

The Strata 1 Boiler is not suitable for installation external to a building. The position chosen for the

boiler must be a structurally sound wall capable of supporting the weight of the boiler and any ancillaries.
The position should allow for access to a condense waste drain nearby or an alternative is to install a
condense sump receptacle and condense disposal pump which should remove the condense waste water
to a remote drain. The wall mounting position of the boiler must allow the boiler to be true plumb vertical
to ensure correct operation of the internal gravity flow condense system. The position for the boiler must
satisfy the requirements of BS6798:1987 or BS6644:1991 as appropriate.

6.0 installation

clearances

For ease of installation, commissioning and maintenance the following minimum clearances should

be observed:-

Sides

50mm

Above

250mm

Below

150mm

Front

450mm

STRATA1

3 8 & 3 8 / 4 6 C O M B I

7

«
...
5
6
7
8
9
...
»

Содержание STRATA1 38 COMBI








































































Отзывы:

Нет отзывов