manualshive.com logo in svg

MHS Boilers STRATA1 38 COMBI, Инструкции по установке, обслуживанию и эксплуатации, Страница: 65 / 71

Поделиться
Скачать
MHS Boilers STRATA1 38 COMBI Скачать руководство пользователя страница 65

65

STRATA1 

3 8   &   3 8 / 4 6   C O M B I

22.0 screen display/diagnosis of faults (contd)

Reset Key

There is a fault with the reset button.

29, 31, 34

Eeprom

There is a fault in the EEPROM in the control.

29

Intern Fault

There is an internal fault in the control panel.

Test Fault

There is a fault with the test button.

29, 31

22.1 (possible) causes of fault

& corrective action

Cause No.

Reason/Action

1.

Operational function No. not set correctly / Check and correct settings. See tables 11,

12, 13.

2.

Unsound electrical connections to flue limit stat / Check and correct.

3. 

Sensor not correctly connected or sensor defective/Check connections and or 

replace sensor.

4. 

Short circuit in wiring / Check and rectify.

5. 

Short circuit in wiring to sensor / Check and rectify.

6. 

Boiler pump not rotating (seized or defective)/Free seized shaft or if defective 

replace pump.

7.

System lacks water / Investigate, refill and vent.

8. 

Connections to heat exchanger limit stat unsound /check & rectify. 

9. 

Unsound electrical connection to fan / Check integrity of fan connection plug.

10. 

Fan blades heavily contaminated / Clean fan.

11. 

Fan is defective / Replace fan.

12 . 

There is no gas supply available / Investigate, restore gas supply.

13. 

Low gas pressure / Investigate and rectify.

14. 

Fuse defective / Check fuses and replace as necessary.

15.  

Gas valve min output setting is incorrect / Check and adjust min output CO

2

%.

16.

Oxidation on burner mounting screws / Loosen and retighten screws.

17.

Poor ignition lead connection to electrode or damp connection or  lead damaged and

shorting to earth / Check and rectify.

Содержание STRATA1 38 COMBI








































































Отзывы:

Нет отзывов