manualshive.com logo in svg

MGL Avionics Vega EMS-1, Руководство по эксплуатации

Поделиться
Скачать
MGL Avionics Vega EMS-1 Скачать руководство пользователя страница 40

Vega EMS-1 Operating Manual

Page 40 

The ULPower ECU Oil Pressure is mapped to the EMS-1 Analog CH 1 (renamed to Oil Press Setup), the ULPower ECU
Oil Temperature to the EMS-1 Analog CH 2 (renamed to Oil Temp Setup) and the ULPower ECU Fuel Pressure to the
EMS-1 Analog CH3 (renamed to Fuel Press Setup). These channels need to be setup accordingly. 

The MGL Avionics RDAC can be used to measure CHT, EGT and MAP.
The EMS-1 also supports the ULPower Aux box 

ULPower recommended settings:

Oil Pressure: max 8 bar (115psi) - normal 2 to 5 bar (30 – 75 psi) above 2000rpm - minimum 0.7 bar
Oil Temperature: Max 120°C (248°F) - Min 50°C (122°F) - Normal between 80°C and 100 °C (175°F – 212°F)
Fuel Pressure: max 3.8 bar (55psi) - normal 3 bar (43,5 psi) - minimum 2.4 bar (35 psi)
Map: Max 1.1 bar (33 inch/kg) – Min. 0.3 bar (9 inch/kg)
EGT: max 860°C (1580°F) - Min. 400°C (700°F) - Normal between 700°C and 800°C (129°F – 1470°F)
CHT: max 180°C (356F°) - Max. continuous 160°C (320°F) - Min. 50°C (125°F)

Содержание Vega EMS-1




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды