Metso NELES NDX 511 Series Скачать руководство пользователя страница 77

Страница: 77 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

14.3.7

Local User Interface

PH2 HEX6

TX7

TX8

Fig. 88 NDX1510_

Fig. 89 NDX_511_ and NDX_512_

Tools for NDX1510_: PH2, TX7

Tools for NDX_511_: PH2, TX7, TX8

Tools for NDX_512_: HEX6, TX7, TX8

•

Remove the main cover by loosening 4 screws.

•

Loosen the display screws.

•

Remove display. Display can be changed when power

is on and device is under control. Replacing the

display does not affect valve position. Note that there

might be other regulations which prevents opening

cover when process is running or power is connected.

•

Mount new display and tighten the screws.

•

Mount main cover and tighten the screws.

WARNING

(Flameproof/Explosion Proof version)

Tightening torque for the housing cover screws

is 15Nm.

14.3.8

Electronics module

Tools for NDX1510_: PH2, TX7, TX20 (60 mm / 2,5 inch

reach required)

Tools for NDX_511_: PH2, TX7, TX8, HEX3 (75 mm / 3

inch reach required)

Tools for NDX_512_: HEX6, TX7, TX8, HEX3 (75 mm / 3

inch reach required), PH2

Disconnect power from the device

•

Shut off supply pressure and make sure that the

actuator pressure is released.

PH2

HEX3 (75 mm/ 3 inch) TX7

HEX6

TX8

TX20

14 MAINTENANCE

AINTENANCE

Содержание NELES NDX 511 Series

























































































Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды

Metso NELES NDX 511 Series, Инструкция по установке, обслуживанию и эксплуатации

Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды