Metso NELES NDX 511 Series Скачать руководство пользователя страница 26

Страница: 26 / 88

NDX VALVE CONTROLLER

8.3

Installation to any rotary actuator

NDX can be easily installed to any rotary actuator when the

following installation rules are followed. In order to guar

antee the best possible position measurement accuracy,

NDX and position feedback magnet must be positioned

according to the following guidelines.

NOTE

Use only Metso original magnets. Bracket and

fixing bolt material should have low magnetic

permeability (e.g. AISI316 or aluminium).

Aim for small mechanical clearance, but avoid contact.

there shall be max 5 mm gap between the magnet and

NDX. Tilt is not critical. Aim for zero eccentricity. Polarity

of the magnet is irrelevant.

Figure 27 shows the exclusion zone. There is no material

limitation outside the exclusion zone, but to guarantee the

optimal performance do not use any magnetic material

inside the zone. Inside the exclusion zone but close to the

”walls” AISI 304 and any austenitic steel can be used.

Fig. 28 Exclusion zone for magnetic material.

ROTARY MOUNTING

Содержание NELES NDX 511 Series

























































































Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды

Metso NELES NDX 511 Series, Инструкция по установке, обслуживанию и эксплуатации

Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды