Metso NELES NDX 511 Series Скачать руководство пользователя страница 61

Страница: 61 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

Status limits are listed and explained in following tables.

Control Performance Diagnostics Limits

Parameter name

Description

Default value

Limits/options

Travel Ratio Limit

Set travel ratio alert limit.

If a value is lower than the limit, a

status is activated for the device

and an event is generated.

0 %

0100 %

Steady State Deviation High Limit

Set steady state deviation high

alert limit.

If a measurement exceeds the

limit, a status is activated for the

device and an event is generated.

5 %

0100 %

Steady State Deviation Last Day

Trend Limit

Set steady state deviation last day

trend alert limit.

A good value for most of the

cases for steady state deviation

is <1 %. More than 5 % means

that control performance is

decreased.”

2 %

0100 %

Positioner Diagnostics Limits

Parameter name

Description

Default value

Limits/options

Total Relay Valve Travel Limit

Set the total relay valve travel

alert limit.

1000 000

010 0000 0000

Date For Total Operation Time

Alert

Select date for next alert.

25 years after first start up

0100 years

Actuator Diagnostics Limits

Parameter name

Description

Default value

Limits/options

Total Actuator Travel Limit

Set the Total Actuator Travel alert

limit.

Counter increases by 1 whenever

the valve has travelled one full

stroke, or 100 % of the valve

movement.

The valve is considered to have

moved when the valve position

c/ 0.5 %

E.g. when the valve moves 10 %,

the counter increases by 0.1

1000 0000

010 0000 0000

Total Actuator Reversals Limit

Set the Total Actuator Reversals

alert limit.

This counter increases by 1

whenever the direction of valve

movement changes.

1000 0000

010 0000 0000

13 DEVICE TYPE MANAGER (DTM)

OPER

ATION

Содержание NELES NDX 511 Series

























































































Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды

Metso NELES NDX 511 Series, Инструкция по установке, обслуживанию и эксплуатации

Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды