Metso NELES NDX 511 Series Скачать руководство пользователя страница 64

Страница: 64 / 88

NDX VALVE CONTROLLER

All parameters

This view lists all configurable device parameters. In offline

mode, All parameters view is the view, which is opened

from the frame application “Offline parameterize” menu

option for parameterizing the device beforehand before

going to online mode or before the device is available.

All parameters view provides a central place to parame

terize the whole device in one place.This allows seasoned

service personnel to quickly configure the device from the

ground up. This view also allows separate configuration

phase and commissioning phase in places, where DTM

instances are configures before there is the physical device

network available. To send offline parameterization to

the device, open the DTM GUI in online mode and send

modifications by clicking Apply button.

Fig. 61

Device Information

Parameter name

Description

Default value

Limits/options

HART Tag

8 characters

NDX

Device Date

Enter a date, e.g. the date when you installed the device.

31.03.2016

Description

Enter a description of the device (max. 16 characters)

NDX

Message

Enter any other relevant information (max. 32 characters)

NDX

HART Long Tag

32 characters, case sensitive, allows consistent implementation

in Host Applications for the longer tag names demanded by

industry users

NDX

HART protocol (restart required)

Restart required after changing the HART protocol.

HART 6

HART 7

Assembly Related

Parameter name

Description

Default value

Limits/options

Positioner Fail Action

Set Positioner Fail Action according to actuator spring

direction.

If you change the value of this parameter, calibrate the device.

When there is linear actuator without mechanical limit in open/

closed end, it is recommended to use Manual calibration.

Open

Position Transmitter Direction

Set position transmitter signal direction.

Normal direction: Output rises when valve angle rises

Normal direction

Reverse

Position Transmitter Fail Value

Position transmitter output when the NDX has a fatal error or is

powered off.

3.5 mA

22.5 mA

Actuator Type

Select actuator type

Select single acting or double acting parameter, depends on

actuator type.

If you change the value of this

parameter, calibrate the device.

Single Acting

Single Acting Actuator

Double Acting Actu

ator

Valve Type

Select valve type.

Defines if device is mounted top of the linear valve or rotary

valve. Dead angle and Beacon position menu are visible if

Rotary is selected as valve type.

If you change the value of this parameter, calibrate the device.

Linear

Rotary

Linear

Dead Angle

This setting is made mainly for segment and ball valves. The

entire signal range is then used for effective valve opening

90° α0.

Refer to device user guide for proper dead angle value for your

valve type.

0 %

0100 %

13 DEVICE TYPE MANAGER (DTM)

Содержание NELES NDX 511 Series

























































































Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды

Metso NELES NDX 511 Series, Инструкция по установке, обслуживанию и эксплуатации

Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды