Merloni EVO3 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 54

background image

Merloni Elettrodomestici

DISHWASHER EVO3

Service manual

EN

03-05-20/0

51-54

Language Issue/Edition

Page

• if C (closed), stops filling and just washes

• if O (open), fills and washes until water level threshold reached or up

to a max. of 8 litres

If the switch is still open at 8 litres, the dishwasher shows the water level alarm.
Probable cause of malfunction: faulty switch or cables disconnected/inverted.

9. WASH MOTOR switched on for 1 minute, ready to fill water if pressure

switch contacts open

• never more than a max. of 8 litres; more than this and the DW shows the

water level alarm.
Probable cause of malfunction: pressure switch faulty or cables
disconnected/inverted.

10.WASH MOTOR, HEATING ELEMENT, DIRECTIONAL CONTROL VALVE on

for 10 seconds

11.Check HIGH PRESSURE sensor status 5 seconds (top and bottom racks

wash), (must be open)

• if the HP sensor stays closed, the DW will show the filter cleaning alarm.

Probable cause of malfunction: HP sensor faulty.

12.Search duo wash parameters, wash only top rack
13.Check HIGH PRESSURE sensor status 15 seconds, (upper rack wash only)

(must be closed)

• if the HP sensor stays closed, the duo wash will not work, the DW will register

an alarm. Probable cause of malfunction: duo wash module faulty, cables
inverted. closed, the duo wash will not work, the DW will register an alarm.
Probable cause of malfunction: duo wash module faulty, cables inverted.

14.Search duo wash parameters, wash upper and lower racks
15.Water heated to 55°C

• if the heating element fails to heat up or the NTC does not register the

temperature, the dishwasher will show the temperature timeout alarm.
Probable cause of malfunction: heating element disconnected or faulty,
or NTC disconnected or faulty, or timer relay jammed

16.Drain O +15 seconds

• if the switch does not open in a max. 4 minutes, the DW will show the

drain timeout alarm.
Probable cause of malfunction: drain pump disconnected or faulty,
pressure switch faulty/cables inverted.

17.….START AUTOTEST CYCLE…… CONTINUE LONG TEST CYCLE…

18.2 litres filled via the TURBINE between rinses

• if the timer does not receive the signal from the turbine but water is

being filled, when the between-rinse pressure switch reaches its threshold
(1.2 litres), it switches the wash motor on and fills water until the
in-cycle pressure switch threshold is reached, for a maximum of 153
seconds from energization of the solenoid valve.
Probable cause of malfunction: turbine disconnected or faulty.

19.WASH MOTOR switched on

«
...
49
50
51
52
53
...
»

Содержание EVO3























































Отзывы:

Нет отзывов

Похожие инструкции для EVO3

FFT-309-311-313

Бренд: Fagor Страницы: 24

3VT913NA - annexe 1

Бренд: BALAY Страницы: 25

3VT913NA - annexe 1

Бренд: BALAY Страницы: 30

Бренд: BALAY Страницы: 2

Бренд: BALAY Страницы: 2

Бренд: BALAY Страницы: 2

3VB350ID - annexe 1

Бренд: BALAY Страницы: 29

FDW-VRR606BDE++

Бренд: FRAM Страницы: 42

Бренд: NEFF Страницы: 30

HG6085D137635QW

Бренд: Hanseatic Страницы: 82

Бренд: A.O. Smith Страницы: 6

Бренд: Gorenje Страницы: 45

Бренд: ECG Страницы: 188

Бренд: ZANKER Страницы: 22

Бренд: Fagor Страницы: 33

Бренд: GE Страницы: 32

WF21T6500 Series

Бренд: Samsung Страницы: 128

Бренд: Electrolux Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды