Merloni EVO3 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 54

background image

Merloni Elettrodomestici

DISHWASHER EVO3

Service manual

EN

03-05-20/0

50-54

Language Issue/Edition

Page

9.2

RESET CODE

With the machine powered up, hold the “P” key down for 5 seconds until you
hear 4 beeps.
To select a new test/Autotest cycle,

wait for 20 seconds with the DW reset,

off and door closed.

9.3

Test and Autotest specifications

1. Switch on the dishwasher.
2. Turbidity sensor reads only if the pressure switch is open (switch input

receives alternating current only when open).

• if the max. turbidity reading is detected (clean, connected), the rinse aid

indicator light switches on until the end of the cycle.

• if the min. turbidity reading is detected (dirty, disconnected), the rinse

aid indicator light switches off until the end of the cycle.

• if the rinse aid indicator lights stays off, the turbidity sensor is not working.

Probable cause of malfunction: turbidity sensor disconnected or faulty
or pipe section with light source is dirty, rinse aid indicator light not
working - disconnected.

3. Salt indicator light switches on until end of cycle (at the same time as the

rinse aid indicator light)

• if the salt indicator light stays off, it is not working.

Probable cause of malfunction: salt indicator light disconnected or
faulty connection.

4. 3 litres water filled between rinses via the T (search duo wash

parameters, wash top and bottom racks)

• if the timer does not receive the signal from the turbine but water is

being filled, when the between-rinse pressure switch closes (at 1.2l), it
will switch on the wash motor and fill water until the in-cycle pressure
switch threshold is reached, for a maximum of 153 seconds from
energization of the solenoid valve.
Probable cause of malfunction: turbine disconnected or faulty.

5. 10 second pause, check HIGH PRESSURE sensor status, (must be closed)

• if the HP sensor is found to be open the dishwasher will show the filter

cleaning alarm. Probable cause of malfunction: HP sensor disconnected
or faulty.

6. WASH MOTOR on.
7. 1 litre water filled in-cycle through the TURBINE (4 litres in total), (with

wash motor on)

8. pressure switch interrogation (O-C) (with wash motor on)

N.B.

The Autotest starts at point 18

«
...
48
49
50
51
52
...
»

Содержание EVO3























































Отзывы:

Нет отзывов

Похожие инструкции для EVO3

Millennia EDW24

Бренд: Dacor Страницы: 16

Бренд: Maytag Страницы: 88

Бренд: Samsung Страницы: 44

Бренд: Samsung Страницы: 44

Бренд: Samsung Страницы: 44

WA55CG7500 Series

Бренд: Samsung Страницы: 76

WA70H4210S Series

Бренд: Samsung Страницы: 48

WD106U4SA Series

Бренд: Samsung Страницы: 44

Бренд: Alliance Laundry Systems Страницы: 48

CLW-108i and CLW-128i Installation / Operation / Maintenance M

Бренд: Cole Parmer Страницы: 50

Бренд: Summit Страницы: 1

Бренд: Magic Chef Страницы: 32

Бренд: Hotpoint Страницы: 16

Бренд: Maytag Страницы: 44

Бренд: Indesit Страницы: 72

Бренд: Newworld Страницы: 41

Бренд: Hanseatic Страницы: 80

Бренд: Candy Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды