COPYRIGHT © 1995 MERIT INDUSTRIES, INC.
2
SCORPION™ -+9000 MANUAL
PM1717-0C
4.
Locate the anti-tip bracket on the rear of the
cabinet (see Figure 7). Pull upwards on the
bracket while folding the top section down.
Make sure that the top unit is resting on the
metal support bracket and that the Velcro
loop on the target section securely aligns
with the Velcro hook on the base section.
5.
Standing at the back facing the folded down
target section, place one hand on the target
section and apply a small amount of force
forward to hold the section in place. With
your other hand, take the hinge pin that is
bent to form a handle and pull outward. (See
Figure 8.) Make sure that the hinge pin is
fully removed. Repeat the same procedure
for the other hinge pin.
6.
You are now ready to remove the target
section. Lift the target section upward
slightly and position it over the safety base
hook. Place the target section, HINGE END
ONLY, on the floor.
NOTE:
DO NOT REST THE TARGET SECTION ON HOOD
END. REST IT ON THE HINGE END ONLY. FAILURE
TO DO SO COULD DAMAGE CABLES OR
OVERHEAD DISPLAY.
Reassembly of Target to Base
1.
The reassembly of the target section is very
similar to that of disassembly. Position the
target section so that it is resting on the
metal bracket of the base. Align the hinges
of the target section with the base section
hinge pins. Install the hinge pins, locking
them into position. Refer to Figure 8.
NOTE: YOU MAY HAVE TO LIFT THE TARGET SECTION
SLIGHTLY TO ALLOW THE HINGE PINS TO MOVE
FREELY INTO THE LOCKED POSITION.
2.
Open the base control panel door.
3.
Make sure that the hinge pins are in the
locked position. Next swing the target
section up into its upright position.
4.
Very carefully open the target section front
door. Place the large black assembly knobs
and washers into the hole that they were
removed from during disassembly. (Refer to
“Floor Model Installation”, step 3.)
5.
Locate the overhead light power cable in the
control panel section. Feed your overhead
light power cable down into the base and
reconnect it to the power supply. Also
reconnect the main harness or harnesses
that interconnect between the sections.
6.
Close all doors and reconnect the power
cord to the back of the game. Reposition the
game to the wall and reconnect the safety
chain to the wall. Plug your power cord into
the wall outlet and turn on the power.
Wall Mount Installation
Your dart game is designed for permanent mounting
to any wall constructed in accordance with standard
building codes. Installing your dart cabinet is not
difficult but the following steps must be followed.
Your game comes equipped with a mounting bracket
which attaches to the wall. The complete assembled
cabinet weighs 85 pounds and is supported by the
mounting bracket. The unit attaches to the bracket
by means of four carriage bolt spacers, extending
from the back of the cabinet.
If you aren't familiar with how to locate wall studs or
if you run into a questionable type of wall
construction - GET HELP!!
The following instructions are recommended as one
method of installing your dart game. If you have a
special situation , or a different method, we remind
you that the cabinet will only be as stable as the wall
is and the way that the bracket attaches to the wall.
NOTE
:
BE SURE THAT THE AREA BEHIND THE WALL
DOES NOT CONTAIN WIRES OR PIPES THAT MAY
BE DAMAGED BY THE BRACKET FASTENERS
.
There must be a minimum 9 1/2" clearance on both
sides of the game to allow for door opening and
access to the coin mech.
REFER TO FIGURES 10, 11 and 12 FOR STEPS 1
THROUGH 8.
1.
Find the location of a wall stud by using a
stud finder, a joint in the wall board or
paneling or by measuring in multiples of 16"
from any known stud. Once you think you've
found it, a good way to make sure is to tap
in a small finishing nail about 2" above the
floor. If the stud is there, you should hit it
after putting the nail in about 1/2" to 3/4".