Mercury Axius System Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 60

background image

Section 3 - Troubleshooting

Page 46

CMD-4082082 / 90-8M0052072

eng

FEBRUARY 2011

Steering System

Symptom

Remedy

The steering wheel steers the boat, but operates

without end stops.

The starboard key switch is tuned off. Turn on the starboard key switch.
Check if the starboard power circuit breaker has tripped. Reset the circuit

breaker, if tripped.

Steering wheel does not steer the boat.

Reduce speed and change to joystick for directional control. Check

VesselView for displayed faults.
Check steering clevis pin.
Check harness connectors in steering actuators.
Check steering fluid level and fill if necessary. See

Section 5—

Maintenance

in the appropriate engine Operation, Maintenance, and

Warranty manual.
Contact your Authorized CMD Repair Facility service technician.

Steering works, but the boat is not as responsive.

Turn the key switch to off and back to on.
Check that both engines are operating.
Check the trim. Adjust if necessary.
Check the steering fluid level and fill if necessary. See

Section 5—

Maintenance

in the appropriate engine Operation, Maintenance, and

Warranty manual.
Contact your Authorized CMD Repair Facility service technician

The steering wheel turned past end stop.

Turn the key switch to off and back on to restore steering wheel

self‑centering, cruise control, and to eliminate the fault code.

Trackpad Features

NOTE: See also Electronic Remote Controls for more situations that also involve the ERC.

Symptom

Remedy

Boat control stuck in "DOCK"

mode.

When DTS features are started with both engines running and one engine is turned off, DTS

will get stuck in that feature. Restart the engine to be able to exit the feature.

Boat control stuck in

"THROTTLE ONLY" mode
Boat control stuck in "1 (SINGLE)

LEVER " mode

Auto Pilot

Symptom

Remedy

Track Waypoint not working

Verify the chartplotter is on.
Verify the chartplotter has an active waypoint.
Verify the speed forward is greater than 2.6 knot 3 mph.
Verify the chartplotter is communicating with VesselView. Compare waypoint names. They should

be the same.
Verify the steering wheel has endstops. If no endstops, refer to "Steering System" above.
Verify the GPS working. Turn off the chartplotter and check latitude and longitude on VesselView.

«
...
48
49
50
51
52
...
»

Содержание Axius System





























































Отзывы:

Нет отзывов

Похожие инструкции для Axius System

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: Landoll Страницы: 34

Бренд: FENDT Страницы: 31

Бренд: GE Страницы: 698

Бренд: Hagie Страницы: 141

Бренд: Garmin Страницы: 2

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

Бренд: MacDon Страницы: 2

Marathon Multi600

Бренд: Saeyang Страницы: 21

Бренд: S&C Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды