Mercury Axius System Скачать руководство пользователя страница 15

Страница: 15 / 60

Section 1 - Getting to Know the Axius System

CMD-4082082 / 90-8M0052072

eng

FEBRUARY 2011

Page 11

b. Adjust to the desired tension.

Side cover removed

a -

Detent tension adjustment screw

b -

Handle tension adjustment screw

9. Remove the screw, washer, and handle when the adjustments are complete.
10. Install the side cover. Secure the cover with the three M5 x 10 mm long screws. Tighten the screws to specification.

Description

lb‑in.

lb‑ft

Side cover screws

3.4

–

11. Apply adhesive to the threads of the handle screw.

Tube Ref No.

Description

Where Used

Part No.

Loctite 271 Threadlocker

Threads of handle screw

92-809819

12. Install the washer and the M8 x 45 mm long screw. Tighten the screw to specification.

41350

Location of handle screw and washer

Description

lb‑in.

lb‑ft

Handle screw

28.2

–

41340

Содержание Axius System





























































Результаты поиска

Содержание Axius System

Отзывы:

Бренды по названию

Популярные бренды

Mercury Axius System, Руководство пользователя

Результаты поиска

Содержание Axius System

Отзывы:

Бренды по названию

Популярные бренды