Mercury Axius System Скачать руководство пользователя страница 48

Страница: 48 / 60

Section 3 - Troubleshooting

Page 44

CMD-4082082 / 90-8M0052072

eng

FEBRUARY 2011

If the Engine Guardian System has been activated, reduce throttle speed. The horn will turn off when throttle speed is within the

allowable limit. Consult an Authorized CMD Repair Facility for assistance.

Troubleshooting Charts

Standard Helm Joystick

Symptom

Remedy

Joystick does not control boat.

Both remote control levers are not in neutral. Put the remote control levers in

neutral.
Some of the engines are not running. Start the engine or engines.

Response to joystick inputs are erratic, or

joystick operates independent of input.

Ensure there are no radios or other sources of electronic or magnetic

interference near the joystick.

Joystick does not function properly and a fault

code is set.

Check VesselView for Guardian fault codes that cause engine power reduction.

If found, have the system checked by your Authorized Cummins MerCruiser

Diesel Repair Facility.

Auxiliary Joystick Station (If Equipped)

Symptom

Remedy

Auxiliary joystick does not control boat.

Both remote control levers are not in neutral. Put the remote control levers in neutral.
Some of the engines are not running. Start the engine or engines.
Throttles have been severely derated due to drive train faults. Determine drive train

faults and make corrections or have the system checked by your Authorized Cummins

MerCruiser Diesel Repair Facility.
One or more drives has a gear shift capability fault. Determine gear shift faults and

make corrections or have the system checked by your Authorized Cummins

MerCruiser Diesel Repair Facility.
One or more drives have steering capability faults. Determine steering faults and make

corrections or have the system checked by your Authorized Cummins MerCruiser

Diesel Repair Facility.

Response to auxiliary joystick inputs

are erratic, or joystick operates

independent of input.

Ensure there are no radios or other sources of electronic or magnetic interference near

the joystick.

Auxiliary joystick does not function

properly and a fault indicator light is

flashing.

Check for fault that results in engine power reduction. If no fault is found, have the

system checked by your Authorized Cummins MerCruiser Diesel Repair Facility.

Содержание Axius System





























































Результаты поиска

Содержание Axius System

Отзывы:

Бренды по названию

Популярные бренды

Mercury Axius System, Руководство пользователя

Результаты поиска

Содержание Axius System

Отзывы:

Бренды по названию

Популярные бренды