manualshive.com logo in svg

Mercury Axius System, Руководство пользователя

Поделиться
Скачать
Mercury Axius System Скачать руководство пользователя страница 25

Section 2 - On the Water

CMD-4082082 / 90-8M0052072   

eng

  FEBRUARY  2011

Page  21

1 (Single) Lever

The control system features the ability to command both engines with a single lever. This feature simplifies engine management

during rough sea conditions by allowing you to grasp a single lever to command both engines simultaneously. It has no affect on

joystick function. This mode is not the same as the system feature called Sync.

39566

"1 LEVER" button

To engage 1 (single) lever mode:
1. Place both ERC levers in neutral.
2. Press the "1 LEVER" button located on the DTS trackpad attached to the ERC levers.
3. The "1 LEVER" button lights.
4. Place the ERC port lever into gear.
5. The RPM of both engines raises and lowers simultaneously with movement of the port ERC lever, while the drives remain in

the same gear.

To disengage 1 (single) lever mode:
1. Place both ERC levers in neutral.
2. Press the "1 LEVER" button. The "1 LEVER" button light turns off.

Sync

The control system features Sync, an automatic engine synchronization feature, which enables automatically at key‑up. Sync

monitors the position of both ERC levers. If both levers are within 10% of one another, the port engine synchronizes to the starboard

engine's RPM. The SmartCraft system will automatically disengage Sync at the last 95% of throttle position range to allow each

engine the ability to reach maximum available RPM. Sync cannot engage until its minimum RPM is met.
The indicator light on the "SYNC" button is on when both engines are on. The light is yellow when the engines are not being

synced, at idle and 95% of throttle. The light turns red when the sync feature is engaged.

39567

"SYNC" button

Содержание Axius System





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды