MerCruiser Vazer 100 Скачать руководство пользователя страница 7

Страница: 7 / 118

90-899883182 NOVEMBER 2007

Page iii

MerCathode Kit (if Equipped).........................91

Painting Your Power Package........................92

Serpentine Drive Belt.............................................92

Checking........................................................93

Replacing.......................................................93

Battery...................................................................94

Supplying Cooling Water to the Engine.................95

Supplying Cooling Water to the Engine (Boat out

of the Water)...................................................95

Supplying Cooling Water to the Engine (Boat in

the Water).......................................................96

Section 6 - Storage

Cold Weather (Freezing Temperature) and Extended

Storage..................................................................98

Draining the Vazer 100 Seawater System.....98

Preparing the Power Package for Extended

Storage...........................................................98

Engine and Fuel System Preparation....................99

Battery Storage....................................................100

Power Package Recommissioning......................100

Section 7 - Troubleshooting

Diagnosing EFI Problems....................................102

Engine Guardian System.....................................102

Troubleshooting Charts.......................................102

Starter Motor Will Not Crank Engine, Or Cranks

Slow..............................................................102

Engine Will Not Start Or Is Hard To Start.....102

Engine Runs Rough, Misses And/Or

Backfires.......................................................103

Poor Performance........................................103

Excessive Engine Temperature...................103

Insufficient Engine Temperature..................103

Low Engine Oil Pressure..............................104

Battery Will Not Come Up On Charge..........104

Remote Control Operates Hard, Binds, Has

Excessive Free‑play or Makes Unusual

Sounds.........................................................104

Steering Wheel Turns Hard Or Jerky...........104

Power Trim Does Not Operate (Motor Does Not

Operate).......................................................104

Power Trim Does Not Operate (Motor Operates

But Sterndrive Unit Does Not Move)............105

Section 8 - Customer Assistance Information

Owner Service Assistance...................................108

Local Repair Service.......................................108

Service Away From Home..............................108

Stolen Power Package...................................108

Attention Required After Submersion.............108

Replacement Service Parts............................108

Parts And Accessories Inquiries................109

Resolving A Problem......................................109

Mercury Marine Service Offices......................109

Ordering Literature..............................................110

United States and Canada..............................110

Outside The United States and Canada.........110

Содержание Vazer 100























































































































Результаты поиска

Содержание Vazer 100

Отзывы:

Похожие инструкции для Vazer 100

Бренды по названию

Популярные бренды

MerCruiser Vazer 100, Руководство пользователя

Результаты поиска

Содержание Vazer 100

Отзывы:

Похожие инструкции для Vazer 100

Бренды по названию

Популярные бренды