MerCruiser Vazer 100 Скачать руководство пользователя страница 72

Страница: 72 / 118

Section 5 - Maintenance

Page 64

90-899883182 NOVEMBER 2007

3. Coat the sealing ring on the new filter with engine oil and install.

26262

a -

Oil filter

b -

Sealing ring

Tube Ref No.

Description

Where Used

Part No.

SAE Engine Oil 30W

Oil filter sealing ring.

Obtain Locally

4. Tighten the oil filter securely (following the filter manufacturer's instructions). Do not

overtighten.

5. Fill the engine with oil. See

Filling

6. Supply cooling water to the engine. See

Supplying Cooling Water to the Engine

7. Start the engine, run the engine for three minutes, and check for leaks. Stop the engine.
8. Check the oil level. See

Checking

Power‑Assisted Steering Fluid

IMPORTANT: Use only Quicksilver Power Trim and Steering Fluid or Dexron III automatic

transmission fluid (ATF) in the power‑assisted steering system.
IMPORTANT: Running the pump dry will damage the pump. Always check steering fluid

levels before operating the boat.

Checking

1. Center the sterndrive and stop the engine.

Содержание Vazer 100























































































































Результаты поиска

Содержание Vazer 100

Отзывы:

MerCruiser Vazer 100, Руководство пользователя, Страница: 72 / 118

Результаты поиска

Содержание Vazer 100

Отзывы: