MerCruiser Vazer 100 Скачать руководство пользователя страница 45

Страница: 45 / 118

Section 3 - On The Water

90-899883182 NOVEMBER 2007

Page 37

OPERATION CHART

Operation Chart

BEFORE STARTING

AFTER STARTING

WHILE

UNDERWAY

STOPPING and SHUT

DOWN

Install the bilge drain plug.

Observe all gauges to

check the condition of

the engine. If it is not

normal, stop the

engine.

Frequently observe

all gauges to check

the condition of the

engine. If it is not

normal, stop the

engine.

Shift the remote control

lever to the neutral

position.

Open the engine hatch. Air out the

bilge completely.

Check for fuel, oil,

water, fluid, and

exhaust leaks.

Listen for the audio

alarm.

Turn the ignition key to the

"OFF" position.

Turn the battery switch on, if

equipped.

Check the shift and

throttle control

operation.

Turn the battery switch to

the "OFF" position, if

equipped.

Turn on and run the engine

compartment bilge blower, if

equipped, for 5 minutes.

Check the steering

operation.

Close the fuel shut‑off

valve, if equipped.

Open fuel shut off valve, if

equipped.

Flush the seawater

cooling circuit, if operating

in saltwater, brackish

water, or polluted water.

Place sterndrive in full down (in)

position.

Drain the bilge.

Check the engine oil.
Perform all other checks specified

by your dealer and boat builder.
Listen for the Audio Warning Alarm

to sound when the ignition switch is

in the "ON" position.
Warm‑up the engine at a fast

idle‑RPM for several minutes.

Starting and Stopping the Engine

NOTE: Only perform those functions applicable to your power package.

STARTING THE ENGINE

1. Check all items listed in the Operation Chart.
2. Place the remote control handle in neutral.

NOTICE

Without sufficient cooling water, the engine, the water pump, and other components will

overheat and suffer damage. Provide a sufficient supply of water to the water inlets during

operation.

WARNING

Explosive fumes contained in the engine compartment can cause serious injury or death

from fire or explosion. Before starting the engine, operate the bilge blower or vent the

engine compartment for at least five minutes.

Содержание Vazer 100























































































































Результаты поиска

Содержание Vazer 100

Отзывы:

Бренды по названию

Популярные бренды

MerCruiser Vazer 100, Руководство пользователя

Результаты поиска

Содержание Vazer 100

Отзывы:

Бренды по названию

Популярные бренды