MerCruiser Vazer 100 Скачать руководство пользователя страница 74

Страница: 74 / 118

Section 5 - Maintenance

Page 66

90-899883182 NOVEMBER 2007

2. The coolant level should be between the "MIN" and "MAX" marks.

26259

a -

Coolant recovery bottle

b -

Fill cap

c -

"MAX" line

d -

"MIN" line

NOTE: If the coolant recovery bottle requires filling more than once a year, contact your

authorized Mercury MerCruiser dealer.

3. Check the antifreeze concentration for adequate freeze protection and correct if

necessary. Refer to the

Specifications

section.

4. Add the specified fluid as necessary. See

Filling

Filling

NOTICE

Using propylene glycol antifreeze in the closed cooling system can damage the cooling

system or the engine. Fill the closed cooling system with an ethylene glycol antifreeze

solution suitable to the lowest temperature to which the engine will be exposed.

NOTICE

Without sufficient cooling water, the engine, the water pump, and other components will

overheat and suffer damage. Provide a sufficient supply of water to the water inlets during

operation.

NOTE: Add coolant only when engine is at normal operating temperature.

1. Remove the fill cap from the coolant recovery bottle.
2. Fill to the "MAX" line with the specified coolant.

Tube Ref No.

Description

Where Used

Part No.

122

Extended Life Antifreeze/

Coolant

Closed Cooling System

92-877770K1

3. Install the fill cap onto the coolant recovery bottle.

Changing

Contact your authorized Mercury MerCruiser dealer.

Содержание Vazer 100























































































































Результаты поиска

Содержание Vazer 100

Отзывы:

MerCruiser Vazer 100, Руководство пользователя, Страница: 74 / 118

Результаты поиска

Содержание Vazer 100

Отзывы: