MerCruiser Vazer 100 Скачать руководство пользователя страница 102

Страница: 102 / 118

Section 5 - Maintenance

Page 94

90-899883182 NOVEMBER 2007

See your authorized MerCruiser dealer for service if these conditions exist.

CAUTION

Rapid release of the belt tensioner, or allowing the tensioner to snap back quickly, could

cause injury or product damage. Relieve the spring tension slowly.

1. Using a suitable tool, rotate the automatic tensioner and remove tension on the belt.

26264

a -

Automatic tensioner

b -

Suitable tool

2. Replace the serpentine belt. Be sure to use proper belt routing.
3. Carefully release the automatic tensioner and ensure that the belt stays positioned

properly.

4. Check the tension of the serpentine belt.

Description
Deflection

6 mm (1/4 in.)

Battery

Refer to specific instructions and warnings accompanying your battery. If this information

is not available, observe the following precautions when handling a battery.

WARNING

Recharging a weak battery in the boat, or using jumper cables and a booster battery to

start the engine, can cause serious injury or product damage from fire or explosion.

Remove the battery from the boat and recharge in a ventilated area away from sparks or

flames.

WARNING

An operating or charging battery produces gas that can ignite and explode, spraying out

sulfuric acid, which can cause severe burns. Ventilate the area around the battery and

wear protective equipment when handling or servicing batteries.

Содержание Vazer 100























































































































Результаты поиска

Содержание Vazer 100

Отзывы:

Похожие инструкции для Vazer 100

Бренды по названию

Популярные бренды

MerCruiser Vazer 100, Руководство пользователя

Результаты поиска

Содержание Vazer 100

Отзывы:

Похожие инструкции для Vazer 100

Бренды по названию

Популярные бренды