MerCruiser Vazer 100 Скачать руководство пользователя страница 112

Страница: 112 / 118

Section 7 - Troubleshooting

Page 104

90-899883182 NOVEMBER 2007

Low Engine Oil Pressure

Possible Cause

Remedy

Insufficient oil in crankcase.

Check and add oil.

Excessive oil in crankcase (causing it to become

aerated).

Check and remove required amount of oil. Check for

cause of excessive oil (improper filling).

Diluted or improper viscosity oil.

Change oil and oil filter, using correct grade and

viscosity oil. Determine cause for dilution (excessive

idling).

Battery Will Not Come Up On Charge

Possible Cause

Remedy

Excessive current draw from battery.

Turn off non‑essential accessories.

Alternator drive belt loose or in poor condition.

Replace and/or adjust.

Unacceptable battery condition.

Test battery, replace if necessary.

Loose or dirty electrical connections or damaged

wiring.

Check all associated electrical connections and wires

(especially battery cables). Clean and tighten faulty

connections. Repair or replace damaged wiring.

Faulty alternator

Test alternator output, replace if necessary.

Remote Control Operates Hard, Binds, Has Excessive Free‑play or Makes Unusual

Sounds

Possible Cause

Remedy

Insufficient lubrication on shift and throttle linkage

fasteners.

Lubricate.

Obstruction in shift or throttle linkages.

Remove obstruction.

Loose or missing shift and throttle linkages.

Check all throttle linkages. If any are loose or missing,

see authorized Mercury MerCruiser dealer

immediately.

Shift or throttle cable kinked.

Straighten cable or have authorized Mercury

MerCruiser dealer replace cable if damaged beyond

repair.

Steering Wheel Turns Hard Or Jerky

Possible Cause

Remedy

Low power steering pump fluid level.

Check for leak. Refill system with fluid.

Drive belt loose or in poor condition.

Replace and/or adjust.

Insufficient lubrication on steering components. Lubricate.

Loose or missing steering fasteners or parts.

Check all parts and fasteners if any are loose or missing,

see authorized Mercury MerCruiser dealer immediately.

Contaminated power steering fluid.

See authorized Mercury MerCruiser dealer.

Power Trim Does Not Operate (Motor Does Not Operate)

Possible Cause

Remedy

Blown fuse.

Replace fuse.

Loose or dirty electrical connections or damaged

wiring.

Check all associated electrical connections and wires

(especially battery cables). Clean and tighten faulty

connection. Repair or replace wiring.

Содержание Vazer 100























































































































Результаты поиска

Содержание Vazer 100

Отзывы:

Похожие инструкции для Vazer 100

Бренды по названию

Популярные бренды

MerCruiser Vazer 100, Руководство пользователя

Результаты поиска

Содержание Vazer 100

Отзывы:

Похожие инструкции для Vazer 100

Бренды по названию

Популярные бренды