background image

 

50 

  

MENDOTA EXTENDED LIFETIME PROTECTION AND LIMITED WARRANTY 

MENDOTA GAS FIREPLACE INSERT 

MODEL:  FV33-M-PF2 NAT. & L.P. 

 

Mendota Division of Johnson Gas Appliance Company, 520 E Avenue N.W. Cedar Rapids, Iowa 52405, extends this Extended Lifetime Protection and Limited 
Warranty to the original purchaser of a Mendota Gas Fireplace Insert, Serial Number 

 

, which is limited and used under normal home conditions. 

 

STANDARD WARRANTY: 

 
JOHNSON GAS APPLIANCE CO., MENDOTA DIVISION, WARRANTS THAT YOUR NEW MENDOTA GAS FIREPLACE INSERT IS FREE FROM 
MANUFACTURING AND MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM THE DATE OF INSTALLATION, SUBJECT TO THE 
FOLLOWING CONDITIONS AND LIMITATIONS: 
 

EXTENDED LIFETIME WARRANTY: 

 
THE HEAT EXCHANGER, THE BURNER TUBE, THE COMBUSTION CHAMBER AND THE OUTER SHIELD OF THE MENDOTA GAS FIREPLACE 
INSERT ARE WARRANTED FOR THE LIFETIME OF THE ORIGINAL OWNER, SUBJECT TO PROOF OF PURCHASE AND THE FOLLOWING 
CONDITIONS AND LIMITATIONS: 
 
1) This new Mendota Fireplace Insert must be installed and serviced by a competent, authorized service contractor.  It must be installed and operated at all times 
in accordance with the installation and operating instructions furnished with the Fireplace.  All adjustments to logs, coals   or burner must be made by an author-
ized Mendota Service person.  
 
This limited warranty does not cover the cost of service calls, the cost of labor to remove or install parts covered by this limited warranty, freight or other trans-
portation expenses that may be incurred in connection with obtaining performances under this limited warranty.  The remedy for damages as the result of any 
defects in this product which have been warranted herein is limited to replacement parts and does not include any incidental, indirect or consequential damages or 
expenses sustained in connection with the products, including damages to property, except as provided by law. 
 
2) This warranty is non-transferable and is made to the original retail purchaser, provided the purchase was made through an authorized Mendota  dealer. 
 
Mendota is not responsible for any damage to or malfunction of the Insert unless caused by a defect in material or workmanship from normal home use.  Damage 
caused by abuse, improper installation or operation, installation by unqualified personnel or breach of the conditions of this limited warranty will excuse Mendota 
from performance of any part of the limited warranty.   This warranty does not cover glass or log breakage. 
 
Mendota has the right to investigate and inspect the exact original fireplace and materials, in the event a claim is made (without alterations or tampering), to de-
termine whether the claimed damage or malfunction was caused by abuse, improper installation or other cause outside this warranty.  Mendota is not responsible 
for any repairs or material purchases that have not received prior written approval from Mendota. 
 
NOTE:  Minor warping of certain parts or discoloration is normal and is not a defect covered by this limited warranty.  Over-firing of your Mendota Fireplace 
Insert can cause major warping of parts.  Over-firing above rated nameplate specifications is contrary to the manufacturer's instructions and WILL void this war-
ranty. 
This warranty may not be extended by our representatives in any manner.  The company neither assumes, nor authorizes any third party to assume, on its behalf, 
any other liabilities with respect to the sale of this Mendota product. 
 
3) Mendota may at its discretion, fully discharge all obligations of this warranty by refunding the wholesale price of the defective part(s). 
4) All other warranties - expressed or implied - with respect to the product, its components and accessories, or any obligation/liabilities on the part of the company 
are hereby expressly excluded.  Products made by other manufacturers, sold with the Fireplace or thereafter, are not covered by this limited warranty.  The use of 
unauthorized components will make this warranty null and void. 
 
This warranty shall be effective only if the original purchaser of the Mendota appliance is registered with Mendota Division within thirty (30) days of the date of 
purchase.  Such registration or the failure to register shall not be deemed to created any obligation or liability by the manufacturer and this warranty with its con-
ditions and limitations shall be the only procedure for obtaining any rights against the manufacturer and expresses the sole obligation and responsibilities of the 
manufacturer which are offered to the original purchaser and accepted upon purchase of the appliance. 
 
Mendota Division, reserves the right to make changes at any time without notice, in design, material, specifications, prices and the right to discontinue styles and 
products. 
Some states do not allow the exclusions of limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above 
limitation or exclusion may not apply to you.  This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.  

Содержание m91





















































Отзывы: