manualshive.com logo in svg

Meinberg IMS-GNS181, Руководство по установке

Поделиться
Скачать
Meinberg IMS-GNS181 Скачать руководство пользователя страница 49

4.2 General GNSS Antennae

Some Meinberg devices use alternate GNSS receivers which support other satellite systems like GLONASS,
Galileo or BeiDou, in addition to GPS. These receivers can’t be operated directly with the standard Meinberg
antenna/converter unit described in chapter "Meinberg GPS Receiver", so they require a different kind of antenna.

There are two different antenna versions available, one of which is more suited for stationary installation,
while the other one should be preferred for mobile applications.

4.2.1 GNSS Antenna for Stationary Installation

The

Multi GNSS Antenna

is an active GNSS antenna which can receive the signals of the GPS, GLONASS,

Galileo and Beidou satellite systems. It is very well suited for stationary installations, operates with a 5V DC
supply voltage provided by the receiver, and has an integrated surge protection.

The antenna cable length can be up to 70 meters if a H155 low-loss coaxial cable is used.

Mounting and Installation of the GNSS/L1 Antenna

Multi GNSS Antenna

free view to the sky!

Type-N female

Type-N male

MEINBERG GNSS

Type SMA male 

female

Connection to earth rail

(Protective Earth)

cable diameter ca. 1,5 mm Ø

as short as possible

Figure: Schematic diagram of mounting the Multi GNSS Antenna

46

Date: 20th March 2020

IMS-GNS181 Setup Guide

Содержание IMS-GNS181






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды