Meatest M-142 Скачать руководство пользователя страница 98

Страница: 98 / 122

M-142 Multifunction Calibrator

MEATEST, s.r.o.

User Manual v48

I/D (instrument identification)

*IDN?

This command returns the identification of the manufacturer, model, serial number and firmware revision.

The reply is formatted as follows:

MEATEST,M-142,412341,4.6

Operation complete

*OPC

<cr>

This command sets the OPC bit in the ESR (Event Status Register) when all pending operations are complete.

Operation complete?

*OPC?

<cr>

This command returns “1” to the output queue after all pending operations are complete.

Operation complete?

*OPC?

<cr>

This command returns “1” to the output queue after all pending operations are complete.

Wait-to-Continue command

*WAI

<cr>

Prevents the instrument from executing any further commands or queries until all previous remote commands
have been executed.

Reset

*RST

<cr>

This command resets the calibrator to its initial status.

Test operation

*TST?

<cr>

This command executes an internal self-test. Return the self-test result (“0” for pass or “1” for fail).

Status byte reading (IEEE488 only)

*STB?

<cr>

This query returns the Status Byte Register including the MSS bit.

Содержание M-142



























































































































Результаты поиска

Содержание M-142

Отзывы:

Бренды по названию

Популярные бренды

Meatest M-142, Инструкции по эксплуатации

Результаты поиска

Содержание M-142

Отзывы:

Бренды по названию

Популярные бренды