Meatest M-142 Скачать руководство пользователя страница 88

Страница: 88 / 122

M-142 Multifunction Calibrator

MEATEST, s.r.o.

User Manual v48

•

OFF or 0 - deactivates the output

If query is sent, M142 returns ON if the output is active or OFF if it is inactive

Example:

OUTP 1 <cr> - activates the output

OUTP ? <cr> - the calibrator returns ON or OFF

OUTP :ISEL (?) <CPD> { HIGH | HI50 }

This command activates or deactivates the 1000A current range (using a 50-turn coil).

•

HIGH - deactivates the 50-turn coil

•

HI50 - activates the 50-turn coil (up to 1000A range)

If query is sent, M142 returns HIGH if the 50-turn coil is deactivated or HI50 if it is activated.

Example:

OUTP :ISEL HI50 <cr> activates the 50-turn coil

OUTP :ISEL ? <cr> the calibrator returns HIGH or HI50

SOURce subsystem

This subsystem allows to control the individual functions of M142 calibrator.

Keyword

Parameters

[SOURce]

: FUNCtion

[: SHAPe] (?)

<CPD> { DC | SINusoid | PULPositive | PULSymmetrical |

PWMPositive | PWMSymmetrical | PWMNegative | .

SQUare }

: VOLTage

[: LEVEl]

[: IMMediate]

[: AMPLitude] (?)

<DNPD>

: CURRent

[: LEVEl]

[: IMMediate]

[: AMPLitude] (?)

<DNPD>

: RESistance

[: LEVEl]

[: IMMediate]

[: AMPLitude] (?)

<DNPD>

: CAPacitance

[: LEVEl]

[: IMMediate]

[: AMPLitude] (?)

<DNPD>

: POWEr

[: LEVEl]

[: IMMediate]

[: AMPLitude] (?)

<DNPD>

: PHASe

: UNITS (?)

<CPD> { DEG | COS }

[: ADJust] (?)

<DNPD>

: VOLTage

[: LEVEl]

[: IMMediate]

[: AMPLitude] (?)

<DNPD>

: CURRent

[: LEVEl]

Содержание M-142



























































































































Результаты поиска

Содержание M-142

Отзывы:

Бренды по названию

Популярные бренды

Meatest M-142, Инструкции по эксплуатации

Результаты поиска

Содержание M-142

Отзывы:

Бренды по названию

Популярные бренды