manualshive.com logo in svg

Meatest M-142, Инструкции по эксплуатации

Поделиться
Скачать
Meatest M-142 Скачать руководство пользователя страница 48

M-142 Multifunction Calibrator 

                             

 MEATEST, s.r.o.

 

 

  48 

 

User Manual v48

 

12.

 

Keyb.beep .... xx   

ON/OFF

 

This parameter allows the acoustic indication of pressed buttons to be switched off or on. ON and OFF display 
buttons can be used to switch the indication off or on. ON is set by the manufacturer. 

This parameter does not control the acoustic indication of output voltages over 100 V and identification of errors. 

 

13.

 

Keyb.volume .... xx 

 UP/DOWN

 

This parameter allows the volume of acoustic indication to be set. UP and DOWN display buttons allow to set 
the value in the range of 00 to 15. The bigger the value, the louder sound. This parameter controls the volume of 
keyboard  beep  (if  switched  on),  indication  of  output  voltages  over  100  V  and  identification  of  errors  when 
controlling the calibrator.    

 

14.

 

Brightness .... xx  

UP/DOWN

 

This parameter sets the contrast of the display. UP and DOWN display buttons allow to set the value in the range 
of 00 to 15.  

 

15.

 

Rotary change .... xx  ON/OFF

 

This parameter controls the range of functions of the potentiometer. If ON is set, the potentiometer can move the 
cursor  both  to  the  left  and  right  (

  and 

  symbols)  and  up  and  down  (

  and 

  symbols).  If  OFF  is  set,  the 

potentiometer can move the cursor up and down only (

 and 

 symbols). 

 

16.

 

Switch polarity .... xx  ON/OFF

 

This parameter controls the function of the built-in relay. If ON is set, the relay is closes before the test. If OFF is 
set, the relay is opens before the test.  

 

17.

 

Switch activity .... xx  PASS/FAIL

 

This parameter controls the function of the built-in relay. If PASS is set, the relay is active (changes its status) if 
the  test  results  in  PASS  status.  If  FAIL  is  set,  the  relay  is  active  (changes  its  status)  if  the  test results in FAIL 
status. 

 

18.

 

Cal.code .... 00000

 

Entry of calibration code. Calibration code is a five-digit number, which must be entered to access the calibration 
mode. If the calibration code is set to “00000”, this information is displayed in the Setup menu. Calibration code 
can be changed. New calibration code can be directly entered using numeric keyboard and confirmed by pressing 
ENTER.  If  non-zero  calibration  code  is  set,  correct  calibration  code  must  be  entered  to  access  the  calibration 
mode. Non-zero calibration code is not displayed further on the display.  

The  purpose  of  the  calibration  code  is  to  prevent  unauthorized  users  from  changing  the  calibration  of  the 
instrument. 

 

 

 

 

 

Содержание M-142



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды