Meatest M-142 Скачать руководство пользователя страница 97

Страница: 97 / 122

MEATEST, s.r.o.

M-142 Multifunction Calibrator

User Manual v48

<DNPD>
Represents the nominal resistance in Ohms.

Example: to set the multimeter to resistance temperature sensor Pt100 measurement mode:

MEAS :CONF :TEMP : RTD :NRES 100 <cr>

If query is sent, M142 returns the set value of nominal resistance using standard exponential format. Example:
20.5



is returned as 2.001.

MEAS :CONF :TEMP :THER :TYPE (?) <CPD> { B | E | J | K | N | R | S | T }

This command selects the function TC of internal multimeter, sets the type of thermocouple and switches the
multimeter on.

Example: to set the multimeter to thermocouple R measurement mode:

MEAS :CONF :TEMP : THER :TYPE R <cr>

If query is sent, M142 returns the set type of thermocouple { B | E | J | K | N | R | S | T }

MEAS :CONF :TEMP :THER :RJUNction (?) <DNPD>

This command selects the function TC of internal multimeter, sets the temperature of cold junction of selected
thermocouple and switches the multimeter on.

<DNPD>
Represents the temperature expressed in the unit set by the ‘UNIT’ command. In “Technical Data” chapter there
is list of acceptable ranges.

Example: to set the temperature of cold end of thermocouple to 25



MEAS :CONF :TEMP :THER :RJUN 25 <cr>

If query is sent, M142 returns the set temperature using standard exponential format. Example: 20.5



C is returned

as 2.001.

MEAS :CONF :OFF

This command switches the multimeter off.

TEST :RUN <DNPD>

This command starts selected procedure. Number 1 to 10 can be set.

<DNPD>
Represents number of procedure.

Example: to run test procedure 3 :

TEST :RUN 3 <cr>

TEST :RESU ?

M142 returns the result of selected procedure { PASS | FAIL | RUN }.

String „RUN“ is returned if selected procedure isn’t finished.

Содержание M-142



























































































































Результаты поиска

Содержание M-142

Отзывы:

Бренды по названию

Популярные бренды

Meatest M-142, Инструкции по эксплуатации

Результаты поиска

Содержание M-142

Отзывы:

Бренды по названию

Популярные бренды