Mazda SKYACTIV-G 2.5 Скачать руководство пользователя страница 7

Страница: 7 / 101

GENERAL INFORMATION

00-00–4

Symbols

•

There are eight symbols indicating oil, grease, fluids, sealant, and the use of

SST

or equivalent. These symbols

show application points or use of these materials during service.

Advisory Messages

•

You will find several

Warnings

Cautions

Notes

Specifications

and

Upper and Lower Limits

in this

manual.

Warning

•

A Warning indicates a situation in which serious injury or death could result if the warning is ignored.

Caution

•

A Caution indicates a situation in which damage to the vehicle or parts could result if the caution is ignored.

Note

•

A Note provides added information that will help you to complete a particular procedure.

Specification

•

The values indicate the allowable range when performing inspections or adjustments.

Upper and lower limits

•

The values indicate the upper and lower limits that must not be exceeded when performing inspections or

adjustments.

End Of Sie

Symbol

Meaning

Kind

Apply oil

New appropriate engine oil or gear oil

Apply brake fluid

New appropriate brake fluid

Apply automatic transaxle/

transmission fluid

New appropriate automatic

transaxle/

transmission fluid

Apply grease

Appropriate grease

Apply sealant

Appropriate

sealant

Apply petroleum jelly

Appropriate

petroleum jelly

Replace part

O-ring, gasket, etc.

Use SST or

equivalent

Appropriate tools

OIL

BRAKE

BRAKE
FLUID

FLUID

ATF

GREASEG

SEALANT

SST

1A36-1U-12L.book 4 ページ２０１２年１２月１０日　月曜日　午前９時２５分

Содержание SKYACTIV-G 2.5






































































































Результаты поиска

Содержание SKYACTIV-G 2.5

Отзывы:

Бренды по названию

Популярные бренды

Mazda SKYACTIV-G 2.5, Руководство по ремонту

Результаты поиска

Содержание SKYACTIV-G 2.5

Отзывы:

Бренды по названию

Популярные бренды