manualshive.com logo in svg

Mazda SKYACTIV-G 2.5, Руководство по ремонту

Поделиться
Скачать
Mazda SKYACTIV-G 2.5 Скачать руководство пользователя страница 33

MECHANICAL 

01-10–20

Dual-mass Flywheel (MTX)/ Drive Plate (ATX) Installation Bolt Disassembly Note

Dual-mass flywheel installation bolt (MTX)

1. Hold the crankshaft using the 

SST (49 E011 1A0)

.

2. Loosen the bolts uniformly and gradually in the 

order shown in the figure.

Note

•

If the bolt installation holes are not 

positioned properly, perform the following 

procedure:

(1) Install the 

SST (49 S120 710)

 to the dual-

mass flywheel.

(2) Rotate the dual-mass flywheel (secondary 

flywheel side) using the 

SST (49 S120 710)

.

(3) When the bolt installation holes are positioned 

properly, hold the position and remove one of 

the bolts.

(4) After removing the bolt, set up the 

SST (49 

G033 102)

 to lock the dual-mass flywheel 

(secondary flywheel side) against rotation.

Warning

•

If all of the bolts are removed without 

locking the dual-mass flywheel 

(secondary flywheel side) against 

rotation, the dual-mass flywheel (primary 

or secondary flywheel side) may rotate, 

resulting in injury. Therefore, always set 

up the SST (49 G033 102).

•

When the bolts are removed from the 

dual-mass flywheel, always cover the bolt 

holes using tape. If the SST (49 G033 102) is removed while the operator’s finger is inserted in the 

bolt hole, the dual-mass flywheel may rotate and the operator could be injured.

(5) Remove the remaining bolts.

Drive plate installation bolt (ATX)

1. Hold the crankshaft using the 

SST

.

2. Loosen the bolts uniformly and gradually in the 

order shown in the figure.

8

4

1

6

2

7

5

3

49 E011 1A0

ac5wzw00005660

49 E011 1A0

49 S120 710

am6xuw00005540

49 E011 1A0

49 S120 710

49 G033 102

am6xuw00005541

49 E011 1A0

bpe1ze00000092

1A36-1U-12L.book  20 ページ  ２０１２年１２月１０日　月曜日　午前９時２５分

Содержание SKYACTIV-G 2.5






































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды