Mazda SKYACTIV-G 2.5 Скачать руководство пользователя страница 14

Страница: 14 / 101

01-10–1

ENGINE

SECTION

01-10

Toc of SCT

MECHANICAL. . . . . . . . . . . . . . 01-10

TECHNICAL DATA . . . . . . . . . . 01-50

SERVICE TOOLS . . . . . . . . . . . 01-60

Toc of SCT

01-10

MECHANICAL

ELECTRIC VARIABLE VALVE TIMING

MOTOR/DRIVER INSPECTION . . . . . . . 01-10–2

HYDRAULIC VARIABLE VALVE TIMING

ACTUATOR INSPECTION . . . . . . . . . . . 01-10–3

ELECTRIC VARIABLE VALVE TIMING

ACTUATOR INSPECTION . . . . . . . . . . . 01-10–3

OIL CONTROL VALVE (OCV)

INSPECTION . . . . . . . . . . . . . . . . . . . . . 01-10–4

Coil Resistance Inspection

. . . . . . . . . . 01-10–4

Spool Valve Operation Inspection

. . . . . 01-10–4

HYDRAULIC LASH ADJUSTER (HLA)

INSPECTION . . . . . . . . . . . . . . . . . . . . . 01-10–5

ROCKER ARM INSPECTION. . . . . . . . . . 01-10–5

ENGINE OVERHAUL SERVICE

WARNING. . . . . . . . . . . . . . . . . . . . . . . . 01-10–5

ENGINE MOUNTING/DISMOUNTING . . . 01-10–6

Mounting

. . . . . . . . . . . . . . . . . . . . . . . . 01-10–6

Dismounting

. . . . . . . . . . . . . . . . . . . . . 01-10–6

TIMING CHAIN DISASSEMBLY. . . . . . . . 01-10–7

Water Pump Pulley

Disassembly Note

. . . . . . . . . . . . . . . . 01-10–9

Crankshaft Pulley Lock Bolt

Disassembly Note

. . . . . . . . . . . . . . . . 01-10–10

Oil Pan Disassembly Note

. . . . . . . . . . . 01-10–10

Engine Front Cover

Disassembly Note

. . . . . . . . . . . . . . . . 01-10–10

Front Oil Seal Disassembly Note

. . . . . 01-10–11

Chain Tensioner Disassembly Note

. . . 01-10–11

Oil Pump Chain Disassembly Note

. . . . 01-10–12

CYLINDER HEAD DISASSEMBLY (I) . . . 01-10–14

Electric Variable Valve Timing Actuator,

Hydraulic Variable Valve Timing

Actuator Disassembly Note

. . . . . . . . . 01-10–16

Camshaft Cap Disassembly Note

. . . . . 01-10–16

Rocker Arm Disassembly Note

. . . . . . . 01-10–16

HLA Disassembly Note

. . . . . . . . . . . . . 01-10–16

Cylinder Head Disassembly Note

. . . . . 01-10–16

CYLINDER HEAD

DISASSEMBLY (II) . . . . . . . . . . . . . . . . . 01-10–17

Valve Keeper Disassembly Note

. . . . . . 01-10–18

Valve Seal Disassembly Note

. . . . . . . . 01-10–18

CYLINDER BLOCK

DISASSEMBLY (I) . . . . . . . . . . . . . . . . . 01-10–19

Dual-mass Flywheel (MTX)/ Drive

Plate (ATX) Installation Bolt

Disassembly Note

. . . . . . . . . . . . . . . . 01-10–20

Dual-mass Flywheel

Disassembly Note (MTX)

. . . . . . . . . . 01-10–21

Rear Oil Seal Disassembly Note

. . . . . 01-10–21

CYLINDER BLOCK

DISASSEMBLY (II) . . . . . . . . . . . . . . . . 01-10–22

Pilot Bearing Disassembly Note

. . . . . . 01-10–23

Connecting Rod Cap

Disassembly Note

. . . . . . . . . . . . . . . 01-10–23

Connecting Rod Bearing

Disassembly Note

. . . . . . . . . . . . . . . 01-10–23

Piston, Connecting Rod

Disassembly Note

. . . . . . . . . . . . . . . 01-10–23

Snap Ring Disassembly Note

. . . . . . . . 01-10–24

Lower Cylinder Block

Disassembly Note

. . . . . . . . . . . . . . . 01-10–24

Thrust Bearing And Main Bearing

Disassembly Note

. . . . . . . . . . . . . . . 01-10–25

Crankshaft Disassembly Note

. . . . . . . 01-10–25

CYLINDER HEAD INSPECTION. . . . . . . 01-10–25

VALVE SEAT INSPECTION/REPAIR. . . . 01-10–26

VALVE, VALVE GUIDE

INSPECTION . . . . . . . . . . . . . . . . . . . . . 01-10–27

VALVE GUIDE REPLACEMENT . . . . . . . 01-10–29

Removal

. . . . . . . . . . . . . . . . . . . . . . . . 01-10–29

Installation

. . . . . . . . . . . . . . . . . . . . . . 01-10–29

VALVE SPRING INSPECTION . . . . . . . . 01-10–29

CAMSHAFT INSPECTION . . . . . . . . . . . 01-10–30

CYLINDER BLOCK INSPECTION . . . . . 01-10–32

OIL JET VALVE INSPECTION . . . . . . . . 01-10–32

PISTON INSPECTION . . . . . . . . . . . . . . . 01-10–32

PISTON RING INSPECTION . . . . . . . . . . 01-10–33

PISTON PIN INSPECTION . . . . . . . . . . . 01-10–34

PISTON AND CONNECTING ROD

INSPECTION . . . . . . . . . . . . . . . . . . . . . 01-10–35

CONNECTING ROD INSPECTION . . . . . 01-10–35

CONNECTING ROD CLEARANCE

INSPECTION . . . . . . . . . . . . . . . . . . . . . 01-10–35

CRANKSHAFT INSPECTION . . . . . . . . . 01-10–36

DUAL-MASS FLYWHEEL

INSPECTION . . . . . . . . . . . . . . . . . . . . . 01-10–37

Inspection Before Removal

. . . . . . . . . 01-10–37

Inspection After Removal

. . . . . . . . . . . 01-10–38

PILOT BEARING INSPECTION . . . . . . . 01-10–39

BOLT INSPECTION. . . . . . . . . . . . . . . . . 01-10–39

CYLINDER BLOCK ASSEMBLY (I) . . . . 01-10–40

Thrust Bearing And Main Bearing

Assembly Note

. . . . . . . . . . . . . . . . . . 01-10–41

Plate Assembly Note

. . . . . . . . . . . . . . 01-10–42

Lower Cylinder Block

Assembly Note

. . . . . . . . . . . . . . . . . . 01-10–42

1A36-1U-12L.book 1 ページ２０１２年１２月１０日　月曜日　午前９時２５分

Содержание SKYACTIV-G 2.5






































































































Результаты поиска

Содержание SKYACTIV-G 2.5

Отзывы:

Бренды по названию

Популярные бренды

Mazda SKYACTIV-G 2.5, Руководство по ремонту

Результаты поиска

Содержание SKYACTIV-G 2.5

Отзывы:

Бренды по названию

Популярные бренды