Mazda SKYACTIV-G 2.5 Скачать руководство пользователя страница 26

Страница: 26 / 101

MECHANICAL

01-10–13

01-10

4. Move the screwdriver in the direction of the arrow and press the oil pump chain, and then press on the plunger

of the oil pump chain tensioner.

5. Insert a wire with an approx. diameter of 1.4 mm

{0.055 in} or a paper clip into the body hole of the

oil pump chain tensioner with the plunger

pressed.

Note

•

The wire or paper clip secures the plunger,

and the tension can be released.

6. Remove the oil pump chain tensioner.

7. Remove the oil pump chain and balancer shaft

sprocket as a single unit.

8. Remove the oil pump driven sprocket.

End Of Sie

OIL PUMP CHAIN TENSIONER

OIL PUMP CHAIN

BEFORE PRESSING

AFTER PRESSING

OIL PUMP CHAIN TENSIONER

PLUNGER

OIL PUMP DRIVE
SPROCKET

bpe1ze00000065

WIRE OR
PAPER CLIP

bpe1ze00000066

1A36-1U-12L.book 13 ページ２０１２年１２月１０日　月曜日　午前９時２５分

Содержание SKYACTIV-G 2.5






































































































Результаты поиска

Содержание SKYACTIV-G 2.5

Отзывы:

Похожие инструкции для SKYACTIV-G 2.5

Бренды по названию

Популярные бренды

Mazda SKYACTIV-G 2.5, Руководство по ремонту

Результаты поиска

Содержание SKYACTIV-G 2.5

Отзывы:

Похожие инструкции для SKYACTIV-G 2.5

Бренды по названию

Популярные бренды