Mazda SKYACTIV-G 2.5 Скачать руководство пользователя страница 11

Страница: 11 / 101

•

Depending on location:

—

Sealant and gaskets, or both, should be

applied to specified locations. When sealant

is applied, parts should be installed before

sealant hardens to prevent leakage.

—

Oil should be applied to the moving

components of parts.

—

Specified oil or grease should be applied at

the prescribed locations (such as oil seals)

before reassembly.

Adjustment

•

Use suitable gauges and testers when making

adjustments.

Rubber Parts and Tubing

•

Prevent gasoline or oil from getting on rubber

parts or tubing.

Torque Formulas

•

When using a torque wrench-

SST

or equivalent

combination, the written torque must be

recalculated due to the extra length that the

SST

or equivalent adds to the torque wrench.

Recalculate the torque by using the following

formulas. Choose the formula that applies to you.

A : The length of the

SST

past the torque wrench drive.

L : The length of the torque wrench.

bpe2ue00000116

bpe2ue00000117

bpe2ue00000118

Torque Unit

Formula

N·m

[L/(L+A)]

kgf·m

[L/(L+A)]

kgf·cm

[L/(L+A)]

ft·lbf

[L/(L+A)]

in·lbf

[L/(L+A)]

SST

bpe2ue00000119

1A36-1U-12L.book 8 ページ２０１２年１２月１０日　月曜日　午前９時２５分

Содержание SKYACTIV-G 2.5






































































































Результаты поиска

Содержание SKYACTIV-G 2.5

Отзывы:

Похожие инструкции для SKYACTIV-G 2.5

Бренды по названию

Популярные бренды

Mazda SKYACTIV-G 2.5, Руководство по ремонту

Результаты поиска

Содержание SKYACTIV-G 2.5

Отзывы:

Похожие инструкции для SKYACTIV-G 2.5

Бренды по названию

Популярные бренды