Mazda 0000-8F-N02B Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 26

Mazda 0000-8F-N02B Скачать руководство пользователя страница 19

19

4280159 Rev. A 10/10

18

TACHOMETER PROGRAMMING

1. Tachometer Programming - Make sure engine hood is closed!

a. Turn the ignition key to the RUN position.

b. Press and hold the programming button.

After 10 seconds the horn will beep 3 times.

c. Release the programming button.

d. Press and release the programming button a second time.

The horn will beep 4 times, indicating that the system has entered option learn mode.

e. Press and release the brake pedal.

The horn will beep 1 time indicating that the system has

entered tachometer learn mode.

f. Start the vehicle with the ignition key and let engine warm up to a normal idle rate. (Less than

1000 RPMs)

The horn will beep 1 time every 3 seconds indicating the system is monitoring the idle rate.

g. Once the vehicle’s engine has warmed up, press and release the programming button.

The horn will beep 4 times, indicating that the system has learned the current idle rate.

h. Turn the ignition key to the OFF position.

«
...
17
18
19
20
21
...
»

Содержание 0000-8F-N02B



























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды