Maytag LD10D2 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 46

background image

Disassembly Procedures

To avoid the risk of electrical shock, personal injury or
death, disconnect power to oven and discharge
capacitors before following any disassembly procedure.

WARNING

!

24

16023053 Rev. 0

©2004 Maytag Appliances Company

Diode

1. Disconnect power to oven and remove outer case,

(see "Outer Case" procedure).

2. Discharge high voltage capacitor, (see "High Voltage

Capacitor" section).

3. Disconnect diode from high voltage capacitor and

remove screw securing diode to ground.

4. Reassemble in reverse order.

Transformer

1. Disconnect power to oven and remove outer case,

(see "Outer Case" procedure).

2. Discharge high voltage capacitor, (see "High Voltage

Capacitor" section).

3. Disconnect and label wire leads from transformer.
4. Remove screws securing transformer and remove.
5. Reassemble in reverse order.

Fuse Block / Filter Assembly

1. Disconnect power to oven and remove outer case,

(see "Outer Case" section).

2. Disconnect and label wires.
3. Carefully lift rear of fuse block assembly to release

assembly from locating pin.

4. Slide fuse block assembly towards front of oven to

remove.

5. Reassemble in reverse order.

Fuse

Fuse Removal

Fuse is located on the noise filter board.

1. Disconnect power to oven and remove outer case,

(see "Outer Case" section).

2. Remove and replace fuse, reassemble in reverse

order.

CAUTION

!

Before replacing a blown monitor fuse, test the
primary interlock switch, secondary interlock switch,
monitor switch, and power relay contacts for proper
operation. If the monitor fuse is blown by a failed
switch operation, all switches and controller must be
replaced.

Magnetron

Magnetron is mounted on the side of the cavity.

1. Disconnect power to oven and remove outer case,

(see "Outer Case" section).

2. Discharge high voltage capacitor, (see "High Voltage

Capacitor" section).

3. Remove filter assembly from magnetron terminals.
4. Remove air duct.
5. Remove screws securing magnetron to the wave

guide.

Waveguide

R.F.
Gasket

Magnetron

Screws

6. Reassemble in reverse order.

NOTE:

When replacing magnetron, make sure gasket

is in correct position and in good condition.

CAUTION

!

During replacement of magnetron, be certain the R.F.
anode gasket is in place around the anode stud.

WARNING

!

A microwave leakage test must be performed anytime
a magnetron assembly is removed, replaced,
disassembled, or adjusted for any reason.

Fan Motor

1. Disconnect power to oven and remove outer case

(see "Outer Case" section).

2. Discharge high voltage capacitor, (see "High Voltage

Capacitor" section).

3. Remove rear air guide.
4. Remove screws securing diode to back panel.
5. Disconnect and label wires to high voltage capacitor.
6. Remove screws securing fan shroud to back panel

and remove fan shroud from cavity.

«
...
22
23
24
25
26
...
»

Содержание LD10D2















































Отзывы:

Нет отзывов

Похожие инструкции для LD10D2

Бренд: Danby Страницы: 28

Designer DMW799W

Бренд: Danby Страницы: 30

Бренд: Panasonic Страницы: 93

ME21D 6300 Series

Бренд: Samsung Страницы: 138

Бренд: Samsung Страницы: 40

Бренд: Vulcan-Hart Страницы: 2

MQS1075 - MICROWAVE

Бренд: Quasar Страницы: 14

Бренд: Nectre Fireplaces Страницы: 16

Бренд: N-BIOTEK Страницы: 14

Бренд: Daewoo Страницы: 31

Бренд: Logik Страницы: 20

Бренд: Ovention Страницы: 39

Бренд: DeLonghi Страницы: 87

Бренд: Lang Страницы: 28

Бренд: Infiniton Страницы: 28

Бренд: AEG Страницы: 37

Бренд: AEG Страницы: 44

Бренд: AEG Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды