Maytag LD10D2 Скачать руководство пользователя страница 34

Страница: 34 / 46

A–4

16023053 Rev. 0

Operation—LD10MP and LD10MPS

CAUTION

To avoid damaging oven, only heat in microwave oven
when turntable is in place.

CAUTION

To avoid fire, do not dry newspapers or clothes in
microwave oven.

Interrupting Operation

• Open oven door to interrupt operation. Oven fan

continues to operate. Close door and press
START pad to resume oven operation.

• Press

STOP/RESET pad to interrupt operation.

Display continues to show countdown time. Close oven
door and press the

START pad to resume oven

operation and countdown timing.

Canceling Mistakes

• If oven is operating, press

STOP/RESET pad once to

stop oven, then again to clear display.

• If oven door is open and time shows in display, close

oven door and press

STOP/RESET pad to clear

display.

Operating Preprogrammed Pads

Oven has 10 – 20 preprogrammed number pads.
Instructions are written for factory programmed ovens.
Ovens that are reprogrammed can respond differently
than described below.

1. Open oven door, place food in oven, and close oven

door.
• If pad is not pressed within 30 seconds, open and

close oven door again.

2. Press desired number pad.

• Oven operates and time counts down.

3. Oven stops heating and oven signal sounds when

heating timing elapses.

Operating QTY 2X Pads

1. Press QTY 2X pad.
2. Press desired number pad.

Example:

Press QTY 2X pad then pad 1 = 18 sec.

NOTE:

This feature automatically sets the time

preprogrammed for multiple cooking items.
The pad times are not representive of the
preprogrammed double digit option.

Preprogrammed Times and Cook Level

All preprogrammed pads are set at full power.

Option: Single Digit

Pads Heating

Times

10 sec.

20 sec.

30 sec.

45 sec.

1 min.

1:30 min.

2 min.

3 min.

4 min.

5 min.

O ption: D o uble D ig it

P ads H eating

T im es

P ads H e atin g

T im es

10 sec.

20 sec.

40 sec.

30 sec.

1 m in.

45 sec.

1:30 m in.

1 m in.

2 m in.

1:30 m in. 16

3 m in.

2 m in.

4 m in.

3 m in.

6 m in.

4 m in.

8 m in.

5 m in.

10 m in.

Manual Time Entry

Manual Time Entry feature allows the operator to enter
time and power levels, and heat without changing the
preprogrammed pads.

1. Open oven door, place food in oven, and close door.

• Display shows “READY”.
• If pad is not pressed within 30 seconds, open and

close oven door again.

2. Press

TIME ENTRY pad.

• Display shows “00:00”.

3. Press number pads to enter desired cooking time.

• For example, to heat for 2 minutes 30 seconds,

press

2, 3, and 0 pads.

Содержание LD10D2















































Результаты поиска

Содержание LD10D2

Отзывы:

Похожие инструкции для LD10D2

Бренды по названию

Популярные бренды

Maytag LD10D2, Руководство по обслуживанию

Результаты поиска

Содержание LD10D2

Отзывы:

Похожие инструкции для LD10D2

Бренды по названию

Популярные бренды