Maytag LD10D2 Скачать руководство пользователя | Manualshive

Страница: 5 / 46

background image

Important Safety Information

©2004 Maytag Appliances Company

16023053 Rev. 0

5

Recognize this symbol as a SAFETY message

SAVE THESE INSTRUCTIONS

1.

READ

all instructions before using equipment.

2.

READ AND FOLLOW

the specific

“PRECAUTIONS TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY”

.

3.

This equipment

MUST BE GROUNDED

. Connect

only to properly GROUNDED outlet. See

“GROUNDING INSTRUCTIONS”

.

4.

Install or locate this equipment

ONLY

in

accordance with the installation instructions in this
manual.

5.

Some products such as whole eggs and sealed
containers, for example, closed glass jars may
explode and

SHOULD NOT

be

HEATED

in this

oven.

6.

Use this equipment

ONLY

for its intended use as

described in this manual. Do not use corrosive
chemicals or vapors in this equipment. This type
of oven is specifically designed to heat or cook. It
is not designed for industrial or laboratory use.

7.

As with any equipment,

CLOSE SUPERVISION

is necessary when used by

CHILDREN

.

8.

DO NOT

operate this equipment if it has a

damaged cord or plug, if it is not working
properly, or if it has been damaged or dropped.

9.

This equipment, including power cord, must be
serviced

ONLY

by qualified service personnel.

Special tools are required to service equipment.
Contact nearest authorized service facility for
examination, repair, or adjustment.

10.

DO NOT

cover or block filter or other openings

on equipment.

11.

DO NOT

store this equipment outdoors.

DO

NOT

use this product near water, for example,

near a kitchen sink, in a wet basement, or near
a swimming pool, and the like.

12.

DO NOT

immerse cord or plug in water.

13. Keep cord

AWAY

from

HEATED

surfaces.

14.

DO NOT

let cord hang over edge of table or

counter.

15. See door cleaning instructions in “Care and

Cleaning” section.

16.

For commercial use only.

WARNING

!

When using electrical equipment, basic safety precautions should be followed to reduce the risk of burns,
electrical shock, fire, or injury to persons.

a.

DO NOT

overcook food. Carefully attend

equipment if paper, plastic, or other combustible
materials are placed inside the oven to facilitate
cooking.

b.

Remove wire twist-ties from paper or plastic
bags before placing bag in oven.

c.

KEEP

oven

DOOR CLOSED

, turn oven off, and

disconnect the power cord, or shut off power at
the fuse or circuit breaker panel, if materials
inside the oven should ignite. Fire may spread
if door is opened.

d.

DO NOT

use the cavity for storage.

DO NOT

leave paper products, cooking utensils, or food
in oven.

CAUTION

!

To reduce risk of fire in the oven cavity:

«
...
3
4
5
6
7
...
»

Содержание LD10D2















































Отзывы:

Нет отзывов

Похожие инструкции для LD10D2

Бренд: Panasonic Страницы: 11

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 34

Бренд: Panasonic Страницы: 36

NN-C980B, NN-C988B

Бренд: Panasonic Страницы: 44

Бренд: Kuppersbusch Страницы: 60

Бренд: Blaupunkt Страницы: 72

Бренд: Klugmann Страницы: 56

Бренд: MPM Страницы: 32

Бренд: Daewoo Страницы: 23

Бренд: Daewoo Страницы: 32

Бренд: RAMTONS Страницы: 12

Бренд: NEFF Страницы: 72

Бренд: Daewoo Страницы: 24

Бренд: point Страницы: 116

Бренд: Maytag Страницы: 48

Бренд: Scarlett Страницы: 7

Бренд: Yamato Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды