Maytag LD10D2 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 46

background image

12

16023053 Rev. 0

©2004 Maytag Appliances Company

Trouble 1: The following visual conditions indicate a probable failed control circuit.

1. Incomplete segments.

• Segment missing.
• Partial segment missing.
• Digit flickering (Note: Slight flickering is normal.)

2. Colon does not turn on or blink.
3. A distinct change in the brightness of one or more numbers in display.
4. One or more digits in the display are not lighting.
5. Display indicates a number different from one touched, for example, key in 5 and 3 appears in the display.
6. Specific numbers (for example 7 or 9) will not display when key pad is touched.
7. Display does not count down with time blinking or count up during operation.
8. Display obviously jumps in time while counting down.
9. Display counts down too fast while cooking.
10. Each indicator light does not turn on after setting cooking cycle.
11. Display time of day does not reappear when cooking is finshed.

Condition

Check

Result

Cause

Remedy

No input can be
programmed.

Check the connection
between keypad and
controller.

•

Continuity

•

Failed

controller.

•

Replace

controller.

•

No continuity

•

Loose

connection.

•

Repair

connection.

1. Some

inputs

cannot be
programmed.

Replace keypad and check
operation.

•

Everything

works as
specified.

•

Failed

keypad.

•

Replace

keypad.

2. Display

shows

a number or
figure different
from one
touched.

•

Still have

trouble.

•

Failed

controller.

•

Replace

controller.

3. Random

programming
when touching
other pads.

4. Display

is

fixed

at some figure
and can not
accept any
input.

Troubleshooting Procedures (Electronic Models)

«
...
10
11
12
13
14
...
»

Содержание LD10D2















































Отзывы:

Нет отзывов

Похожие инструкции для LD10D2

Бренд: Gaggenau Страницы: 16

PS528-SERIES PS528G

Бренд: Middleby Marshall Страницы: 48

Бренд: NEFF Страницы: 32

Бренд: PowerPoint Страницы: 4

Бренд: Waring Страницы: 12

Бренд: Godrej Appliances Страницы: 204

DOLCEVITA FRR69E

Бренд: Lofra Страницы: 40

Бренд: Mistral Страницы: 43

Бренд: Blanco Страницы: 26

Бренд: Maytag Страницы: 24

Бренд: Kambrook Страницы: 28

Бренд: TECHWOOD Страницы: 19

Бренд: Daewoo Страницы: 6

Бренд: Jenn-Air Страницы: 6

Бренд: Godrej Страницы: 223

Бренд: Jenn-Air Страницы: 21

Бренд: Morphy Richards Страницы: 28

Бренд: Zokop Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды