Maytag LD10D2 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 46

background image

Disassembly Procedures

To avoid the risk of electrical shock, personal injury or
death, disconnect power to oven and discharge
capacitors before following any disassembly procedure.

WARNING

!

©2004 Maytag Appliances Company

16023053 Rev. 0

21

CAUTION

!

A microwave leakage test must be performed anytime
a door assembly is removed, replaced, disassembly, or
adjusted for any reason.

NOTE:

When disassembling door, use caution to

prevent deformation of slats on door frame/
choke assembly.

Control Panel Removal

1. Disconnect power to oven and remove outer case,

(see "Outer Case" procedure).

2. Disconnect and label wires from controller/timer.
3. Open oven door.
4. Remove screw securing top of control panel to

cavity. Lift control panel up and out to release bottom
tabs.

5. Reassemble in reverse order.

NOTE:

Be sure to re-install ground wire when securing

control panel to cavity.

Door Disassembly

1. Disconnect power to oven.
2. Remove oven door, (see "Door Removal").
3. Begin at the bottom of the door near hinge, insert flat

blade screwdriver between choke cover and outer
door panel. Gently pry upward on choke cover to
release tabs. Work in clockwise direction to remove
choke cover.

CAUTION

!

To avoid property damage, care must be taken when
prying choke cover from oven door.

4. Slide latch assembly upward and pull away from door

frame to release tabs from frame.

5. Disconnect latch spring from door frame.
6. Begin at hinge side of door near bottom, insert flat

blade screwdriver between door frame/choke
assembly and outer door panel. Gently pry outer
door panel away from door frame to release tabs.
Work in clockwise direction to remove door frame.

7. Reassemble in reverse order.

Outer
door
panel

Door frame/
choke assembly

Choke
cover

Top
hinge
cap

Latch
assembly

Spring

Slats

«
...
19
20
21
22
23
...
»

Содержание LD10D2















































Отзывы:

Нет отзывов

Похожие инструкции для LD10D2

Бренд: Daewoo Страницы: 42

Бренд: Hamilton Beach Страницы: 20

Combi-Duo Elektro Series

Бренд: Rational Страницы: 72

Бренд: Magic Chef Страницы: 35

Бренд: NEFF Страницы: 32

Бренд: Hotpoint Страницы: 18

Бренд: Rational Страницы: 76

Texas 11 2420117

Бренд: Galileo Страницы: 20

Бренд: Caple Страницы: 28

Бренд: Maytag Страницы: 17

Бренд: GE Страницы: 64

Бренд: GE Страницы: 28

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 24

Бренд: GE Страницы: 28

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды