background image

Component Specifications

!

WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to oven and discharge capacitor
before servicing, unless testing requires power.

16021520 Rev. 0

©2002 Maytag Appliances Company

14

Power Test (Traditional Test Method)

Test equipment required is Amana power test kit R0157397(Fahrenheit), or Menumaster power test kit M95D5

(Celsius).

1. Fill the plastic container to the bottom of the 1000 ml. line with cool tap water.
2. Using the thermometer; stir the water, measure and record the water temperature.

Initial water temperature should be approximately 60

°

F (20

°

C).

3. Place container on the center of the oven shelf and heat the water for 62 seconds.

NOTE:

Use a watch second hand, not the oven timer.

4. Stir the water, measure and record the temperature of the water after heating time is complete.
5. Subtract the starting water temperature (Step 2), from the ending water temperature (Step 4), to obtain the

temperature rise.

6. See the Temperature Chart provided below.

NOTES:

The IEC-705 test method requires precision measurements and equipment. It is not practical to perform

the IEC test in the field. To convert the traditional power test results to the approximate IEC-705 rating,
take the traditional power test results and add 100 watts per magnetron for the unit being tested.

Example:

930

watts output using the traditional power test for model RCS10MP

+ 100

watts (1 magnetrons X 100 watts)

1030

Approximate IEC-705 results

Always perform power test three times for accuracy, changing the water after each test is performed.

Variation or errors in the test procedure will cause a variance in the temperature rise. Additional power
tests should be made if temperature rise appears marginal.

Low line voltage will cause lower temperature rise.

Temperature Chart

ONE MINUTE, THREE SECONDS run time chart for units less than 1550 Watts cooking power

  ∆

T

Cooking

T

Cooking

T

Cooking

T

Cooking

(°F)

Power Output

(°F)

Power Output

(°C)

Power Output

(°C)

Power Output

12

464

22

852

7

490

15

1050

13

504

23

891

8

560

16

1120

14

542

24

930

9

630

17

1190

15

580

25

969

10

700

18

1260

16

620

26

1007

11

770

17

659

27

1046

12

840

18

697

28

1085

13

910

19

736

29

1124

14

980

20

775

30

1162

21

814

31

1201

Содержание 1324704M











































Отзывы: