background image

2

16021520   Rev. 0

©2002 Maytag Appliances Company

Important Notices for Servicers and Consumers

Maytag will not be responsible for personal injury or property damage from improper service procedures. Pride and
workmanship go into every product to provide our customers with quality products.  It is possible, however, that during
its lifetime a product may require service.  Products should be serviced only by a qualified service technician who is
familiar with the safety procedures required in the repair and who is equipped with the proper tools, parts, testing
instruments and the appropriate service information.  IT IS THE TECHNICIANS RESPONSIBLITY TO REVIEW ALL
APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS.

!

WARNING

To avoid risk of severe personal injury or death, disconnect power before working/servicing on appliance to avoid
electrical shock.

To locate an authorized servicer, please consult your telephone book or the dealer from whom you purchased this
product.  For further assistance, please contact:

Customer Service Support Center

CAIR Center

Web Site

Telephone Number

WWW.AMANA.COM ................................................ 1-800-843-0304
WWW.JENNAIR.COM ............................................. 1-800-536-6247
WWW.MAYTAG.COM ............................................. 1-800-688-9900

CAIR Center  in Canada ........................................... 1-800-688-2002
Amana Canada Product ........................................... 1-866-587-2002

Recognize Safety Symbols, Words, and Labels

DANGER

!

DANGER—Immediate hazards which WILL result in severe personal injury or death.

WARNING

!

WARNING—Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION

!

CAUTION—Hazards or unsafe practices which COULD result in minor personal injury, product or property

damage.

Important Information

Содержание 1324704M











































Отзывы: