Mattei BLADE 4 Скачать руководство пользователя страница 26

Страница: 26 / 57

4.02

TI013G0008

Connection to the air distribution
system

Compressed air distribution

Only quali

ed staff should carry

out the connection to the air distri-

bution network and in compliance

with the regulations in force.

The distribution of air aims at bringing

compressed air to utilities, with minimum

pressure loss hence reducing any energy

waste.

To avoid any kind of waste, check all the

distribution equipment pipings and all ac-

cessories at regular intervals.

Filters, regulators, and other accessories

must undergo suitable maintenance.

The section of piping connecting to the

equipment must be

exible and with a dia-

meter not less than the one leaving the ma-

chine.

An isolation valve is also required to remo-

ve the machine from the air network in case

of maintenance.

It is recommended that a hose with an air

nozzle be installed near the machine to al-

low for regular cleaning of the radiator,intake

lter and other parts of the machine. The in-

take air contains a certain amount of water

indicated as relative humidity.

on the compressor easier, leave at least 1 m
clearance from all other sides.

Electrical connection

Only quali

ed personnel should

make the electrical connections, in
compliance with current regulations.

WARNING!!!
For safe maintenance of all
compressor components,
the customer should install a

disconnect switch and circuit breakerof
suitable size as near as possible to the
machine.

The characteristics of the electrical motor

start should be taken into consideration

when choosing the disconnect switch and

circuit breaker.

The size of the power cables between line

disconnect switch and the control board of

the compressor should be made using the

values given on the technical sheet of sec-

tion “SECTION DATA “.

For further details, use the speci

c electri-

cal diagram supplied with the machine or

the general one attached to this Manual.

WARNING !!!

It is to be noted that the machi-
ne should ALWAYS be properly
grounded.

Transportation and handling -

Installation

Compressor

Supply

208

Vac

230

Vac

460

Vac

575

Vac

230

Vac

Single

Phase

(1Ph

Ground)

Three

Phase

(3Ph

Ground)

Содержание BLADE 4


























































Результаты поиска

Содержание BLADE 4

Отзывы:

Похожие инструкции для BLADE 4

Бренды по названию

Популярные бренды

Mattei BLADE 4, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание BLADE 4

Отзывы:

Похожие инструкции для BLADE 4

Бренды по названию

Популярные бренды