Mattei BLADE 4 Скачать руководство пользователя

Страница: 37 / 57

7.04

TI013G0008

Maintenance

Belt Replacement

Be sure that the machine is switched off.

Remove the upper and frontal panel to ac-

cess the compressor. Unscrew the bolts

(Pict.5-pos.1) and adjust the screws (Pict.

4-pos.1) to tight the belts. Remove the belts

and replace them with new ones. Tighten

the belts as described in the previous pa-

ragraph.

Replacement of Oil Filter Element

Replace the oil

lter element each time the

oil is changed.

Be sure that the machine is switched off.

Remove the upper panel of the machine.

Dismantle the

lter element (Pict.7-pos.1)

by using chain tongs and replace it with a

new unit. Before locking the

lter element,

lubricate the gasket. Screw the new

lter

element on using a strap wrench.

Replacement of the Air-Oil separator Fil-
ter Element

Be sure that the machine is switched off.

Open the inspection panel. Dismantle the

lter element (Pict.7-pos.2) by using chain

tongs and replace it with a new unit. Before

locking the

lter element, lubricate the ga-

sket. Screw the new

lter element on using

a strap wrench.

Eliminating the receiver condensate

(Pict. 8)

On receiver version only. Open the tank

drain valve and collect the condensate in-

side the receiver in accordance with regu-

lations in force.

Содержание BLADE 4


























































Результаты поиска

Содержание BLADE 4

Отзывы:

Похожие инструкции для BLADE 4

Бренды по названию

Популярные бренды

Mattei BLADE 4, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание BLADE 4

Отзывы:

Похожие инструкции для BLADE 4

Бренды по названию

Популярные бренды