Matrix T1XE-04 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 86

background image

74

10.3 aSSembly iNSTrUCTioNS

aTTeNTioN

After assembly and installation is complete, the treadmill will need to be calibrated using the auto-calibration procedure outlined in Section 3.5.

do NoT stand on the belt while the auto-calibration sequence is in progress.

Prior to assembling the treadmill, unpack all of the contents of the box and make sure that all necessary components are present. Review the

contents of the hardware package for completeness. Contact Matrix customer service at 866.693.4863 to report any missing items.

aSSembly iNSTrUCTioNS

Please make sure that the power cord is not plugged into the wall outlet while completing the following procedure.

To ensure correct assembly of the treadmill, carefully read and follow these steps:

CHaPTer 10: Treadmill SPeCifiCaTioNS aNd aSSembly GUide

A Cut the yellow banding straps and lift the running deck upward

to remove all contents from underneath the running deck.

B Remove the motor cover and set aside. The motor cover

needs to be removed to gain access to the motor compartment
so that wire harness connections can occur.

NOTE: Do not tighten bolts until step 3 is complete.

STeP 1

STeP 2

A

Open BLUE HARDWARE BAG.

B

Assemble both the left and right console
masts to the treadmill base using item

11-SoCkeT

Head CaP SCreW

and item

12-flaT WaSHer

.

NOTE: The console mast caps are marked with an L if they
are to be used on the left-hand side of the treadmill or an R
if they are to be used on the right-hand side of the treadmill.
If the console mast caps are assembled on the incorrect
side of the treadmill, the unit will not assemble correctly.

«
...
75
76
77
78
79
...
»

Содержание T1XE-04























































































Отзывы:

Нет отзывов

Похожие инструкции для T1XE-04

PRO-FORM QUICKSTART 6.0

Бренд: ICON Health & Fitness Страницы: 24

Бренд: Sunny Health & Fitness Страницы: 21

Бренд: Smooth Fitness Страницы: 21

Бренд: Gold's Gym Страницы: 32

Бренд: Weslo Страницы: 16

Бренд: Sunny Health & Fitness Страницы: 15

Бренд: Sunny Health & Fitness Страницы: 17

Бренд: NordicTrack Страницы: 38

Бренд: strength master Страницы: 16

CARDIOSTRONG TF70

Бренд: SportTiedje Страницы: 44

Бренд: Costway Страницы: 5

Бренд: Hammer Страницы: 19

Pro-Form City T7

Бренд: ICON Health & Fitness Страницы: 36

Бренд: Precor Страницы: 2

Бренд: Spirit Страницы: 31

Бренд: ProForm Страницы: 16

Cadence J2.8 Treadmill

Бренд: Weslo Страницы: 19

Folding Treadmill. T9350HRT T9350HRT

Бренд: Vision Fitness Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды