Matrix T1XE-04 Скачать руководство пользователя страница 6

Страница: 6 / 86

CaUTioN: if you experience chest pain, nausea, dizziness or

shortness of breath, SToP exercising immediately and con-

sult a physician before continuing.

• Donotusetheequipmentinanywayotherthandesignedor

intended by the manufacturer. It is imperative that all Matrix

Fitness System's equipment is used properly to avoid injury.

• Keephandsandfeetclearofmovingpartsatalltimestoavoid

injury.

• Unsupervisedchildrenmustbekeptawayfromthisequipment.

• Donotwearlooseclothingwhileonequipment.

2.2 read aNd SaVe THeSe iNSTrUCTioNS

This treadmill is intended for commercial use. To ensure your

safety and protect the equipment, read all instructions before

operating the MATRIX T1xe-04 treadmill.

When using an electrical product, basic precautions should always

be followed including the following:

daNGer: To reduce the risk of electric shock: always unplug

this equipment from the electrical outlet immediately after

using and before cleaning.

WarNiNG: To reduce the risk of burns, fire, electrical shock

or injury to persons that may be associated with using this

product.

An appliance should never be left unattended when plugged in.

Unplug from the outlet when not in use and before putting on or tak-

ing off parts.

This product must be used for its intended purpose described in this

service manual. Do not use other attachments that are not recom-

mended by the manufacturer. Attachments may cause injury.

To prevent electrical shock, never drop or insert any object into any

opening.

Do not remove the console covers. Service should only be done by

an authorized service technician.

Neveroperatethetreadmillwiththeairopeningblocked.Keepthe

air opening clear, free of lint and hair.

Never operate product if it has a damaged cord or plug, if it is work-

ing improperly, if it has been damaged, or immersed in water.

Do not carry this unit by its supply cord or use the cord as a handle.

Keepanypowercordawayfromheatedsurfaces.

Close supervision is necessary when the treadmill is used by or near

children or disabled persons.

Do not use outdoors.

Do not operate where aerosol (spray) products are being used or

when oxygen is being administered.

To disconnect, turn all controls to the off position, then remove plug

from the outlet.

Connect this treadmill to properly grounded outlets only.

CHaPTer 2: imPorTaNT SafeTy iNSTrUCTioNS

Содержание T1XE-04























































































Результаты поиска

Содержание T1XE-04

Отзывы:

Похожие инструкции для T1XE-04

Бренды по названию

Популярные бренды

Matrix T1XE-04, Руководство по обслуживанию

Результаты поиска

Содержание T1XE-04

Отзывы:

Похожие инструкции для T1XE-04

Бренды по названию

Популярные бренды