Matrix T1XE-04 Скачать руководство пользователя страница 19

Страница: 19 / 86

5.5 maNaGer mode - defaUlTS Tab

fUNCTioN & defaUlTS

deSCriPTioNS

modified

Default Level

Default: 1

This option controls the default program level.

Max: 20

Min: 1

Default Age

Default: 30

This option controls the default user's age used in the

target heart rate calculations.

Maximum: 99

Minimum: 10

Default Weight

Default: 150 lb / 68 kg

This option controls the default user's weight used

in the calorie calculations. Displayed in native units

(PoundsorKilograms).

Max: 400 lb / 182 kg

Min: 50 lb / 22 kg.

Default Height

Default: 68 inch / 173 cm

This option controls the default Height used in the

calorie calculations. Displayed in native units (pounds

or kilograms).

Inch: 40~90

Cm: 101~228

Gender

Default: Male

This option controls the user's default gender.

Male or Female

KeySound

Default: Yes

This option can set the keypad tone to sound or not

sound.

Yes or No

maNaGer mode

Defaults

CHaPTer 5: maNaGer mode

Содержание T1XE-04























































































Результаты поиска

Содержание T1XE-04

Отзывы:

Похожие инструкции для T1XE-04

Бренды по названию

Популярные бренды

Matrix T1XE-04, Руководство по обслуживанию

Результаты поиска

Содержание T1XE-04

Отзывы:

Похожие инструкции для T1XE-04

Бренды по названию

Популярные бренды