Matrix T1XE-04 Скачать руководство пользователя страница 17

Страница: 17 / 86

fUNCTioN & defaUlTS

deSCriPTioNS

modified

Accumulated Distance

Total distance showed in native units (miles or

kilometers).

Cannot be modified.

Accumulated Time

Total time.

Cannot be modified.

Software Versions

Software Version, for display only.

Cannot be modified.

KeySoundDefault:On

This option controls whether a chime sounds

when a button is pressed.

On or Off

Out of Order

Default: OFF

To show out of order on the console if repair is

needed.

On or Off

maNaGer mode

About

5.2 maNaGer mode - aboUT Tab

fUNCTioN & defaUlTS

deSCriPTioNS

modified

Maximum Time

Default: 60 Minutes

This option enables fitness club managers to set the

maximum workout duration during peak and non peak hours

of club traffic.

Max: 99 Minutes

Min: 5 Minutes

Default Time

Default: 30 Minutes

This option controls the default program time.

Max: Max Time

Min: 5 Minutes

Pause Time

Default: 5 Minutes

This option controls the default pause time.

Max: 10 Min: 1

maNaGer mode

Time

5.3 maNaGer mode - Time Tab

CHaPTer 5: maNaGer mode

Содержание T1XE-04























































































Результаты поиска

Содержание T1XE-04

Отзывы:

Похожие инструкции для T1XE-04

Бренды по названию

Популярные бренды

Matrix T1XE-04, Руководство по обслуживанию

Результаты поиска

Содержание T1XE-04

Отзывы:

Похожие инструкции для T1XE-04

Бренды по названию

Популярные бренды