Matrix T1XE-04 Скачать руководство пользователя страница 20

Страница: 20 / 86

5.6 maNaGer mode - TV Tab

CHaPTer 5: maNaGer mode

FUNCTION & DEFAULTS

DESCRIPTIONS

MODIFIED

Default Channel

Default: 3

This option controls the default TV channel on start up.

1-999

Default Volume

Default: 8

This option controls the default TV volume on start up.

Maximum: 17

Minimum: 0

Tuner Available

Default: Yes

This option controls the default TV function. If NO is selected, the TV

tab will be removed from the normal function.

Yes or No

Setup

This option is for setting the TV tuner functions. Press the "-" key on

theNUMBERKEYPADtoenterthisfunction.

N/A

Output

Default: Auto

This option is for setting the TV signal output format. If Auto is

selected, the TV signal output format will be for YPBPR or CVBS

detection.

Auto or CVBS

Remote TV

Default: No

This option allows the controller to work with an external MYE TV.

Yes or No

Remote TV

Default: 1.

This option controls the Remote TV channel on start up.

Maximum: 37

Minimum: 1

Remote TV

Default: 15

This option controls the Remote TV volume on start up.

Maximum: 15

Minimum: 1

MANAGER MODE
TV

Содержание T1XE-04























































































Результаты поиска

Содержание T1XE-04

Отзывы:

Похожие инструкции для T1XE-04

Бренды по названию

Популярные бренды

Matrix T1XE-04, Руководство по обслуживанию

Результаты поиска

Содержание T1XE-04

Отзывы:

Похожие инструкции для T1XE-04

Бренды по названию

Популярные бренды